Lubricate General Electric Telephone 2-9710A Tuning Slider

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Introduzione

This guide will show how to lubricate the volume slider after you have opened up the base of the phone. Your volume slider will operate smooth after completing this guide.

Cosa ti serve

Passo 1 Phone Cord

Lubricate General Electric Telephone 2-9710A Tuning Slider, Phone Cord: passo 1, immagine 1 di 2

Lubricate General Electric Telephone 2-9710A Tuning Slider, Phone Cord: passo 1, immagine 2 di 2

Unplug the device before proceeding.
Using a plastic opening tool, remove the phone cord from the phone jack at the base of the headset.
To release the cable, gently press down on the top plastic tab of the connector.

Traduci

Passo 2

Lubricate General Electric Telephone 2-9710A Tuning Slider: passo 2, immagine 3 di 3

Remove the 7.5 mm screw.
Remove the screw cap.
Pull up the phone cord to remove it from the base.

Traduci

Passo 3 9V Base Battery

Lubricate General Electric Telephone 2-9710A Tuning Slider, 9V Base Battery: passo 3, immagine 1 di 2

Lubricate General Electric Telephone 2-9710A Tuning Slider, 9V Base Battery: passo 3, immagine 2 di 2

Remove the battery compartment door (located on the bottom of the radio) by applying thumb pressure to the area indicated on the battery door.
Slide the door off of the battery compartment.
Remove the battery from the phone.

Traduci

Passo 4 Remove Volume Dial

Lubricate General Electric Telephone 2-9710A Tuning Slider, Remove Volume Dial: passo 4, immagine 1 di 2

Lubricate General Electric Telephone 2-9710A Tuning Slider, Remove Volume Dial: passo 4, immagine 2 di 2

Ensure the phone is unplugged from the phone jack and the electrical source.
Locate the volume dial on the right side of the telephone.
Remove the volume dial by gently grasping it and pulling it away from the base.

Traduci

Passo 5 Remove Screws on the Back

Lubricate General Electric Telephone 2-9710A Tuning Slider, Remove Screws on the Back: passo 5, immagine 1 di 1

Remove the three 12 mm screws with a Phillips #1 screwdriver.
Remove the three 18 mm screws with a Phillips #1 screwdriver.

Traduci

Passo 6 Pry the Back Off

Lubricate General Electric Telephone 2-9710A Tuning Slider, Pry the Back Off: passo 6, immagine 1 di 2

Lubricate General Electric Telephone 2-9710A Tuning Slider, Pry the Back Off: passo 6, immagine 2 di 2

Pry off the base shell using a plastic opener tool.
Set the shell aside.
You now have access to the internal components of the General Electric Telephone 2-9710A.

Traduci

Passo 7 Lubricate General Electric Telephone 2-9710A Tuning Slider

Lubricate General Electric Telephone 2-9710A Tuning Slider, Lubricate General Electric Telephone 2-9710A Tuning Slider: passo 7, immagine 1 di 2

Lubricate General Electric Telephone 2-9710A Tuning Slider, Lubricate General Electric Telephone 2-9710A Tuning Slider: passo 7, immagine 2 di 2

Turn the tuning slider counter clockwise all they way.
Apply lubricant to slider rail
Turn the tuning slider back and forth to distribute lubricant
CAUTION: Make sure lubricant does not circuit board. This can damage the circuit board.