Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

Introduzione

If the pedals on your G27 aren't pressing down correctly, or if they just don't feel comfortable under your feet, you will want to replace the springs in the pedals. This isn't a hard replacement to do, all you need is a screwdriver.

Parti

Nessuna parte specificata.

  1. Remove two screws from each pedal with a 2.5mm allen wrench.
    • Remove two screws from each pedal with a 2.5mm allen wrench.

    • The left two pedals have 30 mm screws and the right-most pedal has 16.3 mm screws.

    • Once these screws are off, take off the front faces on each pedal, they should be very easy to remove.

  2. Flip over the device. Now remove fourteen 15.8 mm screws from the underside of the pedal assembly with a Phillips #1 screwdriver. There are two of these screws under the carpet grip, make sure you don't miss those!
    • Flip over the device. Now remove fourteen 15.8 mm screws from the underside of the pedal assembly with a Phillips #1 screwdriver.

    • There are two of these screws under the carpet grip, make sure you don't miss those!

    • When finished, flip over the device again so that it's in its original position.

  3. Lift the top cover of the device from the front, don't completely remove it yet though, because there are still wires connecting both halves. (NEED PICTURE) Behind the left-most pedal, there are two 7.4mm screws attaching a wire to the top cover. Remove these with a Phillips #1 screwdriver and release the wires. Once the wires are no longer connected to the top cover, remove the cover completely.
    • Lift the top cover of the device from the front, don't completely remove it yet though, because there are still wires connecting both halves. (NEED PICTURE)

    • Behind the left-most pedal, there are two 7.4mm screws attaching a wire to the top cover. Remove these with a Phillips #1 screwdriver and release the wires.

    • Once the wires are no longer connected to the top cover, remove the cover completely.

  4. Simultaneously remove the 10mm screws connecting the pedal to the red piston behind it. This will take two 2.5mm allen wrenches, one for each side of the screw.
    • Simultaneously remove the 10mm screws connecting the pedal to the red piston behind it.

    • This will take two 2.5mm allen wrenches, one for each side of the screw.

    • Once removed, the piston can rotate free of the pedal.

  5. Flip the piston away from the pedal and remove the top half of it. The spring should now be visible. (NEED PICTURE)
    • Flip the piston away from the pedal and remove the top half of it. The spring should now be visible. (NEED PICTURE)

    • Take out the spring, and replace it with a new one.

    • Repeat steps four and five for each pedal that needs a spring replaced.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 8 persone hanno completato questa guida.

Grant Blake

Membro da: 21/04/2015

1.445 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 15-4, Amido Spring 2015 Membro di Cal Poly, Team 15-4, Amido Spring 2015

CPSU-AMIDO-S15S15G4

4 Membri

18 Guide realizzate

Is it possible to replace / renew the potentiometers used for gas / brake?

Dave Pawson - Replica

I replaced the springs and reassembled in reverse order. However, my wheel will no longer power on. Any idea where I would have lost power? Thank you.

matthew.liam.gleason - Replica

What size is the cluch spring

isaacjohnson138 - Replica

6cm length

2cm diameter

hermimaier -

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 10

Ultimi 7 Giorni: 58

Ultimi 30 Giorni: 260

Tutti i Tempi: 12,365