Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Componenti & Strumenti

Strumenti

Parti

  1. On the bottom side of the webcam, remove the stickers from both sides On the bottom side of the webcam, remove the stickers from both sides
    • On the bottom side of the webcam, remove the stickers from both sides

  2. Remove the four Phillips screws.
    • Remove the four Phillips screws.

    • Press the holes to unlock the side covers.

  3. Once you removed the side covers, release all the eight Phillips screws. Once you removed the side covers, release all the eight Phillips screws.
    • Once you removed the side covers, release all the eight Phillips screws.

  4. Remove the lens' crystal cover. Remove the four Phillips screws from the metal support. Remove the microphone's rubbers (one from each side).
    • Remove the lens' crystal cover.

    • Remove the four Phillips screws from the metal support.

    • Remove the microphone's rubbers (one from each side).

  5. Kit per Nintendo Switch

    Una soluzione rapida per tornare in gioco

    Acquista Kit per Switch

    Kit per Nintendo Switch

    Una soluzione rapida per tornare in gioco

    Acquista Kit per Switch
  6. Carefully remove the metal supports from the webcam's base.
    • Carefully remove the metal supports from the webcam's base.

  7. Carefully remove the plastic support's base. Loosen the three screws that secure the electronic circuit.
    • Carefully remove the plastic support's base.

    • Loosen the three screws that secure the electronic circuit.

  8. Disconnect the USB cable connector.
    • Disconnect the USB cable connector.

  9. Remove the electronic circuit.
    • Remove the electronic circuit.

  10. Release the clips that secure the cable holder. Pull that cable holder, out of the camera. Release the clips that secure the cable holder. Pull that cable holder, out of the camera.
    • Release the clips that secure the cable holder. Pull that cable holder, out of the camera.

  11. Front and back images of the webcam's electronic circuit board. Front and back images of the webcam's electronic circuit board.
    • Front and back images of the webcam's electronic circuit board.

  12. The problem was the broken cable on the back of the camera. I've cut the faulty part and redid the connections by welding them and insulated them with heat shrinking tubes.
    • The problem was the broken cable on the back of the camera. I've cut the faulty part and redid the connections by welding them and insulated them with heat shrinking tubes.

  13. Repaired cable and attached to the camera. Coated it with some crepe tape. Camera tested: OK!
    • Repaired cable and attached to the camera. Coated it with some crepe tape. Camera tested: OK!

    • Assemble the webcam following the steps in a reverse order.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 10 persone hanno completato questa guida.

Un ringraziamento speciale a questi traduttori:

100%

Questi traduttori ci stanno aiutando ad aggiustare il mondo! Vuoi partecipare?
Inizia a tradurre ›

Jose Gustavo Abreu Murta

Membro da: 06/07/2010

2.770 Reputazione

7 Guide realizzate

Excellent! Helped me figure out how to get the base off to mount it to an ikea worklamp as a hacky boom.

Cory Elsmore - Replica

thanks for an excellent guide . I am now more positive that it is something I can perform now. Many thanks

Graham Klaer - Replica

im having trouble releasing the 4 screws on step 3!!! the screw driver keeps slipping and i’ve tried a few and another webcam…

Dojo Mats - Sunny - Replica

Dojo, Use the correct screw driver. So easy to unscrew.

If you have damaged the screw head, you can use pliers. You will need to replace the damaged screws.

Jose Gustavo Abreu Murta -

Many thanks for this excellent guide!! Helped me to repair my camera

Samuel Anaya - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 26

Ultimi 7 Giorni: 137

Ultimi 30 Giorni: 575

Tutti i Tempi: 8,821