Salta al contenuto principale

Cosa ti serve

Questo smontaggio non è una guida di riparazione. Per riparare il tuo Lenovo ThinkPad 410, usa il nostro manuale di assistenza.

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Unlatch and remove battery

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Open Acess panel

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Remove Hard drive

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Remove wirless WAN

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Remove DIMM from back

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Remove Keyboard retaing Screw from bottom of system

    • Turn the system over and open the cover. Push the keyboard toward the back and lift it up. Slide it forward to rest it on the palm rest. Disconnect the ribbon cable.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Remove BIOS battery

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Disconnect the two antenna leads from the Wireless WAN card. Remove the two retaining screws. Rotate the card up and pull it out of the slot.

    • Remeber which lead goes where Prior to removing it . Grey is usually MAIN , black AUX

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Remove 14 retaining screws from back

    • The first 9 are required for bezel and touchpad removal .

    • M2 × 14 mm, wafer-head, nylon-coated (6)

    • M2 × 3 mm, wafer-head, nylon-coated (3)

    • The remaining need to be removed for base cover removal

    • M2 × 5 mm, wafer-head, nylon-coated (4)

    • M2 × 10 mm, wafer-head, nylon-coated (1)

    • Note: The FPC cable is attached on the underside of the keyboard bezel assembly. In some models, the Bluetooth daughter card is also attached on the underside of the keyboard bezel assembly.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Turn system over , open , remove 4 retaining screws and the work form one side , using spudger to remove chasis bezel

    • M2 × 3 mm, wafer-head, nylon-coated (4)

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Remove 4 retaining screws

    • M2 × 3 mm, wafer-head, nylon-coated (4)

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    • Remove the two retaining screws on the bottom of the system.

    • M2.5 × 6 mm, wafer-head, nylon-coated (2)

    • Turn the system over and open the cover.

    • Unroute all the wires.

    • Remove the retaining screws.

    • M2.5 × 6 mm, wafer-head, nylon-coated (2)

    • Carefully lift the LCD panel up and out of the chass

kevinleroy

Membro da: 08/13/12

338 Reputazione

1 Guida realizzata

Team

Master Techs Membro di Master Techs

Community

322 Membri

2.541 Guide realizzate

5 Commenti

Uhm, sorry, what about the photos? I don't see any...

JoeMuc2014 - Replica

Still not seeing any photos accompanying the steps listed in the teardown.

Jason Landers - Replica

well. if get short out inside of USB or network line>> that has been stopping the software lunched.

mohammed - Replica

we need teardown of T410

mohammed - Replica

The video shows a teardown of the T410s. It is a lot different from the T410.

Robert Oschmann - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 11

Ultimi 30 Giorni: 45

Tutti i Tempi: 10,477