Aggiusta la tua roba Comunità Store

Lenovo IdeaTab A2109 IO Board Replacement

Introduzione

Use this guide to replace the IO board.

Cosa ti serve

  1. Lenovo IdeaTab A2109 IO Board Replacement, Battery: passo 1, immagine 1 di 1

    • Look at the back of the tablet and locate the speakers on top of the rear cover.

    • There is a smaller indentation in the plastic cover that runs across the top of the device.

    • Wedge the plastic opening tool, under the middle of the cover as shown, then push up and the cover will pop off.

    Traduci

  2. Lenovo IdeaTab A2109 IO Board Replacement: passo 2, immagine 1 di 2 Lenovo IdeaTab A2109 IO Board Replacement: passo 2, immagine 2 di 2

    • Remove SD card if present.

    • Remove two black 3mm Phillips #00 screws.

    Traduci

  3. Lenovo IdeaTab A2109 IO Board Replacement: passo 3, immagine 1 di 2 Lenovo IdeaTab A2109 IO Board Replacement: passo 3, immagine 2 di 2

    • Disconnect battery power connector by pinching the connector with tweezers, and sliding it out of the housing.

    Traduci

  4. Lenovo IdeaTab A2109 IO Board Replacement: passo 4, immagine 1 di 2 Lenovo IdeaTab A2109 IO Board Replacement: passo 4, immagine 2 di 2

    • Remove seven black 3mm Phillips #00 screws.

    • The top right corner screw is underneath a yellow ribbon. Lift the ribbon up without disconnecting it and unscrew the screw.

    Traduci

  6. Lenovo IdeaTab A2109 IO Board Replacement: passo 5, immagine 1 di 2 Lenovo IdeaTab A2109 IO Board Replacement: passo 5, immagine 2 di 2

    • Now you can take the battery out in order to either replace it or continue disassembling the device.

    Traduci

  7. Lenovo IdeaTab A2109 IO Board Replacement, System Board: passo 6, immagine 1 di 3 Lenovo IdeaTab A2109 IO Board Replacement, System Board: passo 6, immagine 2 di 3 Lenovo IdeaTab A2109 IO Board Replacement, System Board: passo 6, immagine 3 di 3

    • Remove two black 3mm Phillips #00 screws.

    • Remove three silver 1.8 mm Phillips #00 screws.

    Traduci

  8. Lenovo IdeaTab A2109 IO Board Replacement: passo 7, immagine 1 di 3 Lenovo IdeaTab A2109 IO Board Replacement: passo 7, immagine 2 di 3 Lenovo IdeaTab A2109 IO Board Replacement: passo 7, immagine 3 di 3

    • Use tweezers to flip up the small black plastic locks on all four connections.

    • Carefully remove each of the exposed ribbons.

    Traduci

  9. Lenovo IdeaTab A2109 IO Board Replacement: passo 8, immagine 1 di 2 Lenovo IdeaTab A2109 IO Board Replacement: passo 8, immagine 2 di 2

    • Disconnect the two speaker connectors by pinching them with tweezers and sliding them out from the system board housing.

    Traduci

  10. Lenovo IdeaTab A2109 IO Board Replacement: passo 9, immagine 1 di 2 Lenovo IdeaTab A2109 IO Board Replacement: passo 9, immagine 2 di 2

    • Use tweezers or your finger nail to disconnect the camera attachment by flipping up the black rectangular connector.

    Traduci

  11. Lenovo IdeaTab A2109 IO Board Replacement: passo 10, immagine 1 di 3 Lenovo IdeaTab A2109 IO Board Replacement: passo 10, immagine 2 di 3 Lenovo IdeaTab A2109 IO Board Replacement: passo 10, immagine 3 di 3

    • Disconnect the HDMI connection with the system board

    • Use a plastic opening tool to pry up the system board, and you will hear a pop as it comes free.

    • Slide out the system board from its housing tab on the upper right corner.

    • Pull the board slowly away from the tab, and it will pop out.

    Traduci

  12. Lenovo IdeaTab A2109 IO Board Replacement, IO Board: passo 11, immagine 1 di 2 Lenovo IdeaTab A2109 IO Board Replacement, IO Board: passo 11, immagine 2 di 2

    • Remove the following two screws:

    • M 5.3 x 1.75 mm #00 phillips screws (silver)

    Traduci

  13. Lenovo IdeaTab A2109 IO Board Replacement: passo 12, immagine 1 di 1

    • Once the screws are out, use the tweezers to pull the board straight out.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 9 persone hanno completato questa guida.

Autore

con 4 altri collaboratori

Brian

Membro da: 04/22/14

565 Reputazione

2 Guide realizzate

Distintivi: 9

+6 altri distintivi

Team

Cal Poly, Team 7-19, Regan Spring 2014 Membro di Cal Poly, Team 7-19, Regan Spring 2014

CPSU-REGAN-S14S7G19

4 Membri

15 Guide realizzate

6 Commenti

Great guide but make sure you REMOVE THE AUX SD CARD FIRST if installed or you will break the card and or card slot.

Other than that, no problems. I got the io board for $26 and I put it in for free.

James Bush - Replica

I need an io board for cheap... I might have to make a guide on how to attempt to repair io card without proper tools and a filed down soldering iron tip

Ember Leona - Replica

Thank you this was helpful. I think I fixed my screen flickers the LCD ribbon is under the battery and the ribbon from the volume board on the right I think that's related to the screen rotation lock. Those needed to be flipped up and reseated. Thanks

Ember Leona - Replica

Thanks Very much

the guide is very clear

i have done the job successfully

omimh - Replica

Excelente guía. Muchas gracias.

Larry Pacheco - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 2

Tutti i Tempi: 4,910