Salta al contenuto principale

Introduzione

Be careful when lifting the WiFi card out of its slot not to damage the slot. Similarly, make sure that once it has been replaced that the two wires are securely connected to the card.

Parti

Nessuna parte specificata.

  1. Turn off the computer, unplug all cables, and let it cool down. Lay the computer flat on its screen.
    • Turn off the computer, unplug all cables, and let it cool down. Lay the computer flat on its screen.

    • Make sure that the work surface is flat and has nothing sharp on it.

  2. Remove the monitor stand screw in the bottom of the stand, and remove the stand completely. Remove the monitor stand screw in the bottom of the stand, and remove the stand completely.
    • Remove the monitor stand screw in the bottom of the stand, and remove the stand completely.

  3. Remove the two screws on the bottom of the computer, one on each side.
    • Remove the two screws on the bottom of the computer, one on each side.

  4. Locate the slot on the right side of the computer next to the screw hole. Use a plastic opening tool or spudger to pry off the rear cover. (Don’t be afraid to use a little force.) Locate the slot on the right side of the computer next to the screw hole. Use a plastic opening tool or spudger to pry off the rear cover. (Don’t be afraid to use a little force.) Locate the slot on the right side of the computer next to the screw hole. Use a plastic opening tool or spudger to pry off the rear cover. (Don’t be afraid to use a little force.)
    • Locate the slot on the right side of the computer next to the screw hole. Use a plastic opening tool or spudger to pry off the rear cover. (Don’t be afraid to use a little force.)

  5. Batterie per PC portatili

    Una soluzione semplice per un grande aumento di potenza.

    Acquista ora

    Batterie per PC portatili

    Una soluzione semplice per un grande aumento di potenza.

    Acquista ora
  6. Once it has been separated, lift to remove. Once it has been separated, lift to remove.
    • Once it has been separated, lift to remove.

  7. Remove the four screws that secure the arm stand. Remove the four screws that secure the arm stand.
    • Remove the four screws that secure the arm stand.

  8. Lift up to remove the arm stand. Lift up to remove the arm stand.
    • Lift up to remove the arm stand.

  9. Remove the 5 screws that secure the EMI cover. Remove the cover. Remove the cover.
    • Remove the 5 screws that secure the EMI cover.

    • Remove the cover.

  10. Remove any tape that secures the WiFi antenna cables. Remove any tape that secures the WiFi antenna cables.
    • Remove any tape that secures the WiFi antenna cables.

  11. Remove the single screw that secures that WiFi card to the motherboard. Remove the single screw that secures that WiFi card to the motherboard.
    • Remove the single screw that secures that WiFi card to the motherboard.

  12. Lift the wifi card and then pull out the card. Lift the wifi card and then pull out the card.
    • Lift the wifi card and then pull out the card.

  13. Locate the two small cables connected to the wifi card and pull gently to disconnect them.
    • Locate the two small cables connected to the wifi card and pull gently to disconnect them.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Jackson Blake

Membro da: 22/01/2018

948 Reputazione

9 Guide realizzate

Team

Cal Poly, Team S16-G3, Banghart Winter 2018 Membro di Cal Poly, Team S16-G3, Banghart Winter 2018

CPSU-BANGHART-W18S16G3

4 Membri

9 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 14

Tutti i Tempi: 234