Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Kodak PixPro AZ251 Motherboard Replacement

Introduzione

In this guide, you will learn how to remove and replace the motherboard of your Kodak PixPro AZ251. Replacing the motherboard may be necessary if your camera does not turn on and you already tried replacing the batteries. For this replacement guide you should be comfortable using a soldering iron.

Cosa ti serve

  1. Kodak PixPro AZ251 Motherboard Replacement, Batteries: passo 1, immagine 1 di 2 Kodak PixPro AZ251 Motherboard Replacement, Batteries: passo 1, immagine 2 di 2

    • Slide switch to open lock position.

    Traduci

  2. Kodak PixPro AZ251 Motherboard Replacement: passo 2, immagine 1 di 2 Kodak PixPro AZ251 Motherboard Replacement: passo 2, immagine 2 di 2

    • Press down on the battery cover and slide outwards to open.

    Traduci

  3. Kodak PixPro AZ251 Motherboard Replacement: passo 3, immagine 1 di 1

    • Remove the batteries.

    Traduci

  4. Kodak PixPro AZ251 Motherboard Replacement, Back Cover: passo 4, immagine 1 di 3 Kodak PixPro AZ251 Motherboard Replacement, Back Cover: passo 4, immagine 2 di 3 Kodak PixPro AZ251 Motherboard Replacement, Back Cover: passo 4, immagine 3 di 3

    • Remove a total of four 5mm JIS #000 screws from around the camera:

    • Two screws from the right side.

    • Two screws from the left side.

    Traduci

  5. Kodak PixPro AZ251 Motherboard Replacement: passo 5, immagine 1 di 1

    • Remove the single 5mm Phillips #00 screw from the bottom.

    Traduci

  6. Kodak PixPro AZ251 Motherboard Replacement: passo 6, immagine 1 di 2 Kodak PixPro AZ251 Motherboard Replacement: passo 6, immagine 2 di 2

    • Open the flash module.

    • Remove the two 6mm JIS #00 screws found inside of the flash housing.

    Traduci

  7. Kodak PixPro AZ251 Motherboard Replacement: passo 7, immagine 1 di 3 Kodak PixPro AZ251 Motherboard Replacement: passo 7, immagine 2 di 3 Kodak PixPro AZ251 Motherboard Replacement: passo 7, immagine 3 di 3

    • Use a plastic opening tool to pry apart both halves of the camera.

    • Remove the back panel.

    Traduci

  9. Kodak PixPro AZ251 Motherboard Replacement, LCD Screen: passo 8, immagine 1 di 2 Kodak PixPro AZ251 Motherboard Replacement, LCD Screen: passo 8, immagine 2 di 2

    • Remove these three JIS #000 screws from the control board:

    • 5mm screw.

    • 4mm screw.

    • 2mm screw.

    Traduci

  10. Kodak PixPro AZ251 Motherboard Replacement: passo 9, immagine 1 di 1

    • Pull the small metal switch plate to the side.

    Traduci

  11. Kodak PixPro AZ251 Motherboard Replacement: passo 10, immagine 1 di 2 Kodak PixPro AZ251 Motherboard Replacement: passo 10, immagine 2 di 2

    • Pry the LCD screen out of the metal housing plate with a plastic opening tool.

    Traduci

  12. Kodak PixPro AZ251 Motherboard Replacement: passo 11, immagine 1 di 2 Kodak PixPro AZ251 Motherboard Replacement: passo 11, immagine 2 di 2

    • Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket.

    • Pull the orange cable out of the socket.

    Traduci

  13. Kodak PixPro AZ251 Motherboard Replacement, Motherboard: passo 12, immagine 1 di 2 Kodak PixPro AZ251 Motherboard Replacement, Motherboard: passo 12, immagine 2 di 2

    • Remove three 4mm JIS #000 screws from the metal housing plate.

    Traduci

  14. Kodak PixPro AZ251 Motherboard Replacement: passo 13, immagine 1 di 1

    • Lift the metal housing plate out using your hands.

    Traduci

  15. Kodak PixPro AZ251 Motherboard Replacement: passo 14, immagine 1 di 1

    • Disconnect the orange cable, connecting the small metal switch plate to the motherboard, by pulling it outwards with tweezers.

    Traduci

  16. Kodak PixPro AZ251 Motherboard Replacement: passo 15, immagine 1 di 2 Kodak PixPro AZ251 Motherboard Replacement: passo 15, immagine 2 di 2

    • Disconnect two orange cables, one at the top and the other at the bottom of the motherboard, by pulling them outwards with tweezers.

    • Use a spudger to flip up the retaining flap on the ribbon cable ZIF socket.

    Traduci

  17. Kodak PixPro AZ251 Motherboard Replacement: passo 16, immagine 1 di 2 Kodak PixPro AZ251 Motherboard Replacement: passo 16, immagine 2 di 2

    • Remove the rectangular black cushion pad on the bottom left of the motherboard by pulling it upwards with your hands.

    • Use a spudger to flip up the retaining flap on the ribbon cable ZIF socket.

    • Disconnect the orange cable by pulling it outwards with tweezers.

    Traduci

  18. Kodak PixPro AZ251 Motherboard Replacement: passo 17, immagine 1 di 1

    • Remove the two 4mm JIS #000 screws from the motherboard.

    Traduci

  19. Kodak PixPro AZ251 Motherboard Replacement: passo 18, immagine 1 di 1

    • Desolder two pairs of electrical cable connections on the top left of the motherboard using the soldering iron.

    • Desolder the metal connector joining the two parts of the motherboard using the soldering iron.

    • The unsoldering steps are not shown.

    Traduci

  20. Kodak PixPro AZ251 Motherboard Replacement: passo 19, immagine 1 di 1

    • Lift the motherboard up using your hands.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 5 persone hanno completato questa guida.

Autore

con 2 altri collaboratori

Deborah Oliveira

Membro da: 02/22/18

319 Reputazione

2 Guide realizzate

Distintivi: 9

+6 altri distintivi

Team

USF Tampa, Team S1-G1, Cagle Spring 2018 Membro di USF Tampa, Team S1-G1, Cagle Spring 2018

USFT-CAGLE-S18S1G1

4 Membri

7 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 36

Tutti i Tempi: 1,571