Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Kodak EasyShare LS743 Capacitor Replacement

Cosa ti serve

  1. Kodak EasyShare LS743 Capacitor Replacement, Battery: passo 1, immagine 1 di 1
    • Using your fingernail, open the battery cover.

  2. Kodak EasyShare LS743 Capacitor Replacement: passo 2, immagine 1 di 1
    • Slide the orange latch sideways to eject the battery.

    • Remove the battery from the battery slot.

  3. Kodak EasyShare LS743 Capacitor Replacement, Kodak EasyShare LS743 Camera Case Disassembly: passo 3, immagine 1 di 3 Kodak EasyShare LS743 Capacitor Replacement, Kodak EasyShare LS743 Camera Case Disassembly: passo 3, immagine 2 di 3 Kodak EasyShare LS743 Capacitor Replacement, Kodak EasyShare LS743 Camera Case Disassembly: passo 3, immagine 3 di 3
    • Using a Phillips #00 screwdriver, remove two 5.39 mm screws next to the battery slot.

    • Remove the metal piece holding down the lanyard, then remove the lanyard.

  4. Kodak EasyShare LS743 Capacitor Replacement: passo 4, immagine 1 di 3 Kodak EasyShare LS743 Capacitor Replacement: passo 4, immagine 2 di 3 Kodak EasyShare LS743 Capacitor Replacement: passo 4, immagine 3 di 3
    • Using a Phillips #00 screwdriver, remove seven screws located on the outside case of the camera.

    • One 6.25 mm screw is located on the top right corner, right to the "OK" button.

    • Four 4.45 mm screws are on the bottom of the camera.

    • Two 2.95 mm screws are on the left side of the camera, above the USB port.

  5. Kodak EasyShare LS743 Capacitor Replacement: passo 5, immagine 1 di 2 Kodak EasyShare LS743 Capacitor Replacement: passo 5, immagine 2 di 2
    • Carefully remove the rear camera casing.

    • Carefully remove the front camera casing.

  6. Kodak EasyShare LS743 Capacitor Replacement, Capacitor: passo 6, immagine 1 di 3 Kodak EasyShare LS743 Capacitor Replacement, Capacitor: passo 6, immagine 2 di 3 Kodak EasyShare LS743 Capacitor Replacement, Capacitor: passo 6, immagine 3 di 3
    • The capacitor can store electricity even when the camera is off! Do not touch it until you have safely discharged it.

    • Connect the two capacitor wires briefly with a pair of metal tweezers to discharge it. You may see a small spark.

    • Remove 8 screws.

    • 2 screws in the front (2X 4.31mm).

    • 2 screws on the bottom (2X3.30MM).

    • 4 screws in the back (3x 3.33mm, and 1x 4.34mm).

  7. Kodak EasyShare LS743 Capacitor Replacement: passo 7, immagine 1 di 1
    • Remove and set aside the tripod mount.

  8. Kodak EasyShare LS743 Capacitor Replacement: passo 8, immagine 1 di 1
    • Pull the black latch outward slightly to release the flex cable.

    • Carefully disconnect the orange flex cable.

  9. Kodak EasyShare LS743 Capacitor Replacement: passo 9, immagine 1 di 1
    • Desolder both wires and remove them.

  10. Kodak EasyShare LS743 Capacitor Replacement: passo 10, immagine 1 di 2 Kodak EasyShare LS743 Capacitor Replacement: passo 10, immagine 2 di 2
    • Remove the capacitor (attached by adhesive) and desolder.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Team

Cal Poly, Team 2-8, Johann Summer 2010 Membro di Cal Poly, Team 2-8, Johann Summer 2010

CPSU-JOHANN-R10S2G8

5 Membri

16 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 2,253