Salta al contenuto principale

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

KitchenAid Professional 600 Power Cord Replacement

Cosa ti serve

  1. KitchenAid Professional 600 Power Cord Replacement, Top Cover: passo 1, immagine 1 di 1
    • Take out the screw which holds on the silver band using a Phillips #2 screwdriver.

    • Remove the silver band.

  2. KitchenAid Professional 600 Power Cord Replacement: passo 2, immagine 1 di 1
    • Remove the four Phillips #2 screws located around the mixer where the band was removed.

    • This picture only shows two of the screw that you need to remove. The other two are on the exact opposite side of the mixer.

  3. KitchenAid Professional 600 Power Cord Replacement: passo 3, immagine 1 di 1
    • Remove the top of the mixer to reveal the inner parts.

    • The top should lift off, but may not if it is stuck. A sharp strike from the back with the hand may unstick it. It will slide forward about a 3/8 of an inch. Push it back again from the front and it should be free enough to lift.

  4. KitchenAid Professional 600 Power Cord Replacement, Speed Selector: passo 4, immagine 1 di 1
    • Locate the selector switch.

    • Remove the two Phillips #2 screws holding the selector switch in place.

  5. KitchenAid Professional 600 Power Cord Replacement: passo 5, immagine 1 di 3 KitchenAid Professional 600 Power Cord Replacement: passo 5, immagine 2 di 3 KitchenAid Professional 600 Power Cord Replacement: passo 5, immagine 3 di 3
    • Unplug the cords attached the drive motor to the switch.

    • We suggest numbering them left from right so they are reattached to the replacement part in the right order.

  6. KitchenAid Professional 600 Power Cord Replacement: passo 6, immagine 1 di 1
    • Pull out the Selector Switch.

  7. KitchenAid Professional 600 Power Cord Replacement, Drive Motor: passo 7, immagine 1 di 1
    • Remove the two Phillips #2 screws holding the motor in place, located near the fan at the back of the motor.

    • The picture only shows one of the screws. The other screw is located on the exact opposite side of the motor.

  8. KitchenAid Professional 600 Power Cord Replacement: passo 8, immagine 1 di 1
    • Pull upward to remove the motor.

  9. KitchenAid Professional 600 Power Cord Replacement, Power Cord: passo 9, immagine 1 di 1
    • Remove the Phillips #2 screw attaching the green grounding wire to the frame of the mixer.

  10. KitchenAid Professional 600 Power Cord Replacement: passo 10, immagine 1 di 1
    • Remove the three Phillips #2 screws that connect the top portion of the mixer to the "neck" of the mixer.

  11. KitchenAid Professional 600 Power Cord Replacement: passo 11, immagine 1 di 1
    • Remove the top portion of the mixer from the "neck" of the mixer.

    • This will make removing the power cord much easier.

  12. KitchenAid Professional 600 Power Cord Replacement: passo 12, immagine 1 di 1
    • You can now remove the power cord from the mixer.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Luke

Membro da: 04/11/16

1.353 Reputazione

5 Guide realizzate

Team

Cal Poly, Team 25-4, Maness Spring 2016 Membro di Cal Poly, Team 25-4, Maness Spring 2016

CPSU-MANESS-S16S25G4

4 Membri

18 Guide realizzate

2 Commenti

So helpful thank you. I've got my mixer cord changer and the mixer is working now. Unfortunately there's always only one speed, high. Any suggestions?

Britter C - Replica

Any idea where I can buy the power cord itself?

Jaeger Amzallag - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 14

Ultimi 30 Giorni: 67

Tutti i Tempi: 5,629