Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

KitchenAid Classic Mixer K45SSWH Gasket Replacement

Cosa ti serve

  1. KitchenAid Classic Mixer K45SSWH Gasket Replacement, Motor Housing Cover: passo 1, immagine 1 di 2 KitchenAid Classic Mixer K45SSWH Gasket Replacement, Motor Housing Cover: passo 1, immagine 2 di 2

    • Using a spudger, gently pry off the aluminum drip ring.

    Traduci

  2. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 2, immagine 1 di 1

    • Using a 4 mm pin punch and hammer, hammer the pin until it is dislodged from the planetary gear cover.

    Traduci

  3. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 3, immagine 1 di 2 KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 3, immagine 2 di 2

    • Using a spudger, pry the planetary gear cover from the mixer shaft.

    Traduci

  4. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 4, immagine 1 di 1

    • Using a flathead screwdriver, remove the five 28 mm front motor housing screws.

    • Using the same flathead screwdriver, remove the two 28 mm locking screws.

    • One of the locking screws contains a safety locking mechanism. Do not interchange these screws with the front motor housing screws.

    Traduci

  6. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 5, immagine 1 di 1

    • Turn your device around. Using the same flathead screwdriver, remove the two 28 mm rear locking screws.

    • One of the rear motor housing screws contains a safety locking mechanism. Do not interchange these screws with the front motor housing screws.

    Traduci

  7. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 6, immagine 1 di 2 KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 6, immagine 2 di 2

    • Using a Phillips #2 screwdriver, remove the 10 mm screw from top of back cover.

    • The rear cover is now completely free from the mixer.

    Traduci

  8. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 7, immagine 1 di 2 KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 7, immagine 2 di 2

    • Carefully pull the power cord from the notch in back of the mixer.

    • The motor housing cover is now completely free from the base of the mixer.

    Traduci

  9. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 8, immagine 1 di 1

    • Lift the motor housing cover from the mixer base.

    • Be sure to place the cover upside-down to prevent grease from leaking out.

    Traduci

  10. KitchenAid Classic Mixer K45SSWH Gasket Replacement, Gasket: passo 9, immagine 1 di 2 KitchenAid Classic Mixer K45SSWH Gasket Replacement, Gasket: passo 9, immagine 2 di 2

    • Use a butter knife or putty knife to remove grease from around the gasket.

    • Place grease in motor housing cover.

    Traduci

  11. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 10, immagine 1 di 1

    • Lift the gasket up with your hands or a spuger and remove it.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 7 persone hanno completato questa guida.

Autore

con 6 altri collaboratori

Joey Gavin

Membro da: 10/13/14

244 Reputazione

1 Guida realizzata

Distintivi: 6

+3 altri distintivi

Team

Cal Poly, Team 14-28, Maness Fall 2014 Membro di Cal Poly, Team 14-28, Maness Fall 2014

CPSU-MANESS-F14S14G28

4 Membri

22 Guide realizzate

2 Commenti

I got all the way to the last step of replacing the pin when i notice the mixer seemed to lock there in place and not move. What did i do wrong?

Dawn dawn6463@yahoo.com

Dawn Bennett - Replica

Hi there - There is a gasket around the engine part that you can see in step 7. Mine tore when I removed it. Is that a bad thing? I put the machine back together and it seems to work.

RES - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 6

Ultimi 7 Giorni: 34

Ultimi 30 Giorni: 106

Tutti i Tempi: 9,163