Salta al contenuto principale

KitchenAid Classic Mixer K45SSWH Gasket Replacement

Cosa ti serve

  1. KitchenAid Classic Mixer K45SSWH Gasket Replacement, Motor Housing Cover: passo 1, immagine 1 di 2 KitchenAid Classic Mixer K45SSWH Gasket Replacement, Motor Housing Cover: passo 1, immagine 2 di 2
    • Using a spudger, gently pry off the aluminum drip ring.

  2. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 2, immagine 1 di 1
    • Using a 4 mm pin punch and hammer, hammer the pin until it is dislodged from the planetary gear cover.

  3. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 3, immagine 1 di 2 KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 3, immagine 2 di 2
    • Using a spudger, pry the planetary gear cover from the mixer shaft.

  4. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 4, immagine 1 di 1
    • Using a flathead screwdriver, remove the five 28 mm front motor housing screws.

    • Using the same flathead screwdriver, remove the two 28 mm locking screws.

    • One of the locking screws contains a safety locking mechanism. Do not interchange these screws with the front motor housing screws.

  5. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 5, immagine 1 di 1
    • Turn your device around. Using the same flathead screwdriver, remove the two 28 mm rear locking screws.

    • One of the rear motor housing screws contains a safety locking mechanism. Do not interchange these screws with the front motor housing screws.

  6. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 6, immagine 1 di 2 KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 6, immagine 2 di 2
    • Using a Phillips #2 screwdriver, remove the 10 mm screw from top of back cover.

    • The rear cover is now completely free from the mixer.

  7. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 7, immagine 1 di 2 KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 7, immagine 2 di 2
    • Carefully pull the power cord from the notch in back of the mixer.

    • The motor housing cover is now completely free from the base of the mixer.

  8. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 8, immagine 1 di 1
    • Lift the motor housing cover from the mixer base.

    • Be sure to place the cover upside-down to prevent grease from leaking out.

  9. KitchenAid Classic Mixer K45SSWH Gasket Replacement, Gasket: passo 9, immagine 1 di 2 KitchenAid Classic Mixer K45SSWH Gasket Replacement, Gasket: passo 9, immagine 2 di 2
    • Use a butter knife or putty knife to remove grease from around the gasket.

    • Place grease in motor housing cover.

  10. KitchenAid Classic Mixer K45SSWH Gasket Replacement: passo 10, immagine 1 di 1
    • Lift the gasket up with your hands or a spuger and remove it.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 7 persone hanno completato questa guida.

Joey Gavin

Membro da: 10/13/14

244 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 14-28, Maness Fall 2014 Membro di Cal Poly, Team 14-28, Maness Fall 2014

CPSU-MANESS-F14S14G28

4 Membri

22 Guide realizzate

2 Commenti

I got all the way to the last step of replacing the pin when i notice the mixer seemed to lock there in place and not move. What did i do wrong?

Dawn dawn6463@yahoo.com

Dawn Bennett - Replica

Hi there - There is a gasket around the engine part that you can see in step 7. Mine tore when I removed it. Is that a bad thing? I put the machine back together and it seems to work.

RES - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 18

Ultimi 30 Giorni: 78

Tutti i Tempi: 9,283