Aggiusta la tua roba Comunità Store

Kenwood DNX571HD Cooling Fan Replacement

Introduzione

If your Kenwood DNX571HD has been overheating, the cooling fan on the back of the Kenwood DNX571HD car stereo may have failed. Follow this guide to replace it.

Cosa ti serve

  1. Kenwood DNX571HD Cooling Fan Replacement, CD/DVD Drive: passo 1, immagine 1 di 2 Kenwood DNX571HD Cooling Fan Replacement, CD/DVD Drive: passo 1, immagine 2 di 2

    • Unscrew the four 3.5mm side screws with a Phillips #1 screwdriver.

    • There are two screws per side.

    Modifica

  2. Kenwood DNX571HD Cooling Fan Replacement: passo 2, immagine 1 di 3 Kenwood DNX571HD Cooling Fan Replacement: passo 2, immagine 2 di 3 Kenwood DNX571HD Cooling Fan Replacement: passo 2, immagine 3 di 3

    • Use a spudger to unhook the plastic clips on the sides and top of the front panel. There are two clips on each side and one clip on the top.

    • Place the spudger between the plastic tab and the metal case and gently lift the spudger away from the case.

    Modifica

  3. Kenwood DNX571HD Cooling Fan Replacement: passo 3, immagine 1 di 1

    • Pull the top of the front panel out and down to remove front panel.

    • Remove the front panel gently so as not to damage the ribbon cables behind it.

    Modifica

  4. Kenwood DNX571HD Cooling Fan Replacement: passo 4, immagine 1 di 3 Kenwood DNX571HD Cooling Fan Replacement: passo 4, immagine 2 di 3 Kenwood DNX571HD Cooling Fan Replacement: passo 4, immagine 3 di 3

    • Unscrew the three 5mm screws from the top of the device using a Phillips #1 screwdriver.

    • Lift up to remove the top casing.

    Modifica

  6. Kenwood DNX571HD Cooling Fan Replacement: passo 5, immagine 1 di 1

    • Lift the CD drive carefully to expose the attached cable underneath.

    Modifica

  7. Kenwood DNX571HD Cooling Fan Replacement: passo 6, immagine 1 di 2 Kenwood DNX571HD Cooling Fan Replacement: passo 6, immagine 2 di 2

    • Flip up the black clasp with a spudger to disconnect the large white ribbon cable connecting the CD drive to the board underneath.

    Modifica

  8. Kenwood DNX571HD Cooling Fan Replacement, Cooling Fan: passo 7, immagine 1 di 1

    • Carefully unplug the fan power cord with the tweezers.

    Modifica

  9. Kenwood DNX571HD Cooling Fan Replacement: passo 8, immagine 1 di 2 Kenwood DNX571HD Cooling Fan Replacement: passo 8, immagine 2 di 2

    • Unscrew the three 5mm length screws with the Phillips #1 screwdriver.

    • Remove the metal plate

    • Removing the plate will damage the heat sink compound. This will need to be replaced during reassembly.

    Modifica

  10. Kenwood DNX571HD Cooling Fan Replacement: passo 9, immagine 1 di 2 Kenwood DNX571HD Cooling Fan Replacement: passo 9, immagine 2 di 2

    • Unscrew the three 5.5mm long screws with a Phillips #1 screwdriver.

    Modifica

  11. Kenwood DNX571HD Cooling Fan Replacement: passo 10, immagine 1 di 3 Kenwood DNX571HD Cooling Fan Replacement: passo 10, immagine 2 di 3 Kenwood DNX571HD Cooling Fan Replacement: passo 10, immagine 3 di 3

    • Remove the four 5.5mm screws with the Phillips #1 screwdriver.

    Modifica

  12. Kenwood DNX571HD Cooling Fan Replacement: passo 11, immagine 1 di 1

    • Lift the top part of the unit up from the lower chassis.

    Modifica

  13. Kenwood DNX571HD Cooling Fan Replacement: passo 12, immagine 1 di 2 Kenwood DNX571HD Cooling Fan Replacement: passo 12, immagine 2 di 2

    • Remove the two 13mm long screws with a Phillips #1 screwdriver.

    • Gently thread the power cable through the circuit boards to separate the fan from the body of the stereo.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 12

Tutti i Tempi: 906