Aggiusta le tue cose Community Store

Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement

Introduzione

Replacement of the LCD board on any Kaffelogic Nano or Nucleus Link coffee roaster with a D or P prefix serial number.

Cosa ti serve

  1. Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Removing Front Panel Screws: passo 1, immagine 1 di 2 Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Removing Front Panel Screws: passo 1, immagine 2 di 2

    • Remove the 6x 2.5mm Hex screws on the left and right side of the roaster.

    • Take care not to damage the buttons while maneuvering the front panel, with all six screws removed it may fall away.

    Modifica

  2. Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Lift the closure: passo 2, immagine 1 di 2 Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Lift the closure: passo 2, immagine 2 di 2

    • Hold the front panel steady while removing the plastic top/closure.

    Modifica

  3. Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Removing the front panel: passo 3, immagine 1 di 1

    • Pull away the front panel carefully.

    Modifica

  5. Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Removing the rear panel: passo 4, immagine 1 di 3 Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Removing the rear panel: passo 4, immagine 2 di 3 Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Removing the rear panel: passo 4, immagine 3 di 3

    • Remove the last 2.5mm Hex screw securing the rear panel.

    • Pull up on the rear panel to remove it from the roaster.

    Modifica

  6. Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Access granted: passo 5, immagine 1 di 2 Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Access granted: passo 5, immagine 2 di 2

    • Set the panels aside somewhere safe and bask in the beauty of your naked roaster.

    Modifica

  7. Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Remove ribbon cable: passo 6, immagine 1 di 3 Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Remove ribbon cable: passo 6, immagine 2 di 3 Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Remove ribbon cable: passo 6, immagine 3 di 3

    • Gently remove the ribbon cable from the PCB.

    Modifica

  8. Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Remove PCB screws: passo 7, immagine 1 di 3 Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Remove PCB screws: passo 7, immagine 2 di 3 Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Remove PCB screws: passo 7, immagine 3 di 3

    • Unscrew the 4x PH2 PCB screws.

    • These screws are captive to the PCB.

    Modifica

  9. Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Remove PCB: passo 8, immagine 1 di 3 Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Remove PCB: passo 8, immagine 2 di 3 Kaffelogic Nano 7/LINK (D-P Serial) LCD Board Replacement, Remove PCB: passo 8, immagine 3 di 3

    • Carefully remove the display PCB.

    • You may replace the ribbon cable while you have the panels off.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 2 altri collaboratori

Kaffelogic

Membro da: 07/23/25

2.098 Reputazione

18 Guide realizzate

Distintivi: 5

+2 altri distintivi

Team

Kaffelogic Staff Membro di Kaffelogic Staff

Community

3 Membri

18 Guide realizzate

0Commenti sulla guida

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 9

Tutti i Tempi: 50