Aggiusta la tua roba Comunità Store

Jumper Angelsounds JPD-100S The Transducer Replacement

Introduzione

Step by step, this guide will demonstrate how to change the transducer of the Angel Sound device

Cosa ti serve

  1. Jumper Angelsounds JPD-100S The Transducer Replacement, Motherboard: passo 1, immagine 1 di 1

    • Access the battery compartment

    • Remove the battery compartment lid and set it aside.

    • Disconnect the battery and set it aside.

    Traduci

  2. Jumper Angelsounds JPD-100S The Transducer Replacement: passo 2, immagine 1 di 2 Jumper Angelsounds JPD-100S The Transducer Replacement: passo 2, immagine 2 di 2

    • Puncture the sticker in the battery compartment with a spudger to access the screw beneath it.

    Traduci

  3. Jumper Angelsounds JPD-100S The Transducer Replacement: passo 3, immagine 1 di 1

    • Remove the 7mm Phillips #1 screw from the battery compartment.

    • Place the screw in a secure place.

    Traduci

  5. Jumper Angelsounds JPD-100S The Transducer Replacement: passo 4, immagine 1 di 2 Jumper Angelsounds JPD-100S The Transducer Replacement: passo 4, immagine 2 di 2

    • Begin prying open the device.

    • Insert a plastic opening tool into the side groove about 2cm from the pink plastic component and pry open one side of the device.

    • Once the side is separated, leave the opening tool inside to prevent the two sides from closing.

    Traduci

  6. Jumper Angelsounds JPD-100S The Transducer Replacement: passo 5, immagine 1 di 2 Jumper Angelsounds JPD-100S The Transducer Replacement: passo 5, immagine 2 di 2

    • Insert another plastic opening tool into the groove opposite to the side of the tool already inserted.

    • Create separation on that side until the white plastic component comes off entirely.

    • Place the white plastic component in a secure place.

    Traduci

  7. Jumper Angelsounds JPD-100S The Transducer Replacement: passo 6, immagine 1 di 1

    • With your hand, remove the pink component.

    Traduci

  8. Jumper Angelsounds JPD-100S The Transducer Replacement: passo 7, immagine 1 di 1

    • Remove the 7mm Phillips #1 screw in the middle of the motherboard.

    Traduci

  9. Jumper Angelsounds JPD-100S The Transducer Replacement, The Transducer: passo 8, immagine 1 di 1

    • Unsolder the Black cable

    Traduci

  10. Jumper Angelsounds JPD-100S The Transducer Replacement: passo 9, immagine 1 di 2 Jumper Angelsounds JPD-100S The Transducer Replacement: passo 9, immagine 2 di 2

    • Unsolder the red cables from the metal plates.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 1 altro collaboratore

Muosa Almubarak

Membro da: 09/29/15

101 Reputazione

1 Guida realizzata

Distintivi: 2

Team

USF Tampa, Team 6-1, Remmell Fall 2015 Membro di USF Tampa, Team 6-1, Remmell Fall 2015

USFT-REMMELL-F15S6G1

6 Membri

6 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 3

Tutti i Tempi: 287