Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Componenti & Strumenti

Introduzione

If the lights on the board aren’t working, the buttons on aren’t responsive, or Bluetooth is no longer functioning correctly, you may need to replace the motherboard. This guide will give you step-by-step instructions on how to replace the motherboard on the Jabra Speak 510.

  1. Using a metal spudger, peel back the foam pad on the bottom of the device to reveal six screws. Using a metal spudger, peel back the foam pad on the bottom of the device to reveal six screws.
    • Using a metal spudger, peel back the foam pad on the bottom of the device to reveal six screws.

  2. Remove the six 20 mm T6 screws from the bottom of the device.
    • Remove the six 20 mm T6 screws from the bottom of the device.

  3. Remove the back plate and the grey foam underneath. Remove the back plate and the grey foam underneath.
    • Remove the back plate and the grey foam underneath.

  4. Nintendo Switch Kits

    A quick fix to get back in the game

    Shop Switch Kits

    Nintendo Switch Kits

    A quick fix to get back in the game

    Shop Switch Kits
  5. Use a small, pointed metal spudger to  release the plastic tabs connecting the faceplate to the bottom of the speaker. A small cable connects the faceplate to the device. Carefully disconnect the cable before fully opening  the device. Slowly flip the device open like a clam shell.
    • Use a small, pointed metal spudger to release the plastic tabs connecting the faceplate to the bottom of the speaker.

    • A small cable connects the faceplate to the device. Carefully disconnect the cable before fully opening the device.

    • Slowly flip the device open like a clam shell.

    • There are several wires soldered to the motherboard that prevent the faceplate from detaching completely.

  6. Using the T6 Torx Screwdriver, remove the four (4mm) screws. Using the T6 Torx Screwdriver, remove the four (4mm) screws.
    • Using the T6 Torx Screwdriver, remove the four (4mm) screws.

  7. After removing the screws, take out the center covering to free the motherboard by lifting the tabs and pulling it off.
    • After removing the screws, take out the center covering to free the motherboard by lifting the tabs and pulling it off.

  8. Peel off the white adhesive to desolder the connections underneath. Desolder the wires connected to the motherboard.
    • Peel off the white adhesive to desolder the connections underneath.

    • Desolder the wires connected to the motherboard.

    • You can find soldering tips in the How To Solder and Desolder Connections guide.

    • Keep track of where the wires are connected. When re-assembling you will have to connect the wires in the correct spot.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

Jordan Murphy

Membro da: 16/02/2016

546 Reputazione

3 Guide realizzate

Team

IUPUI, Team 2-3, Harley Spring 2016 Membro di IUPUI, Team 2-3, Harley Spring 2016

IUPUI-HARLEY-S16S2G3

4 Membri

4 Guide realizzate

Great walk-through... thanks

Walaa Maher - Replica

Be very careful when desoldering the connector cables! The soldering lugs are poor quality and tend to tear off the PCB

Thomas Sprenger - Replica

Hello

Where I can buy the motherboard replacement?

Regards

Lobo Gris - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 5

Ultimi 7 Giorni: 27

Ultimi 30 Giorni: 123

Tutti i Tempi: 3,009