Salta al contenuto principale

Introduzione

Aggiorna il tuo hard drive per una migliore capacità di memoria!

  1. Rimuovi le dieci viti seguenti, che fissano il case inferiore al MacBook Pro Unibody da 13":
    • Rimuovi le dieci viti seguenti, che fissano il case inferiore al MacBook Pro Unibody da 13":

    • Sette viti con testa a croce da 3 mm.

    • Tre viti con testa a croce da 13,5 mm.

    Compare the short screws carefully before reinstalling them. The shouldered screws go in the holes on the front edge.

    David Kilbridge - Replica

    Before I started removing any screws I took a piece of paper and drew the bottom of the laptop and put a piece of double-sided tape in the spot where each screw goes. That way when I took out the screws, I could put them on the tape so I knew exactly which screw went in which spot. I did the same thing for dismantling the inside on another sheet of paper, then a third sheet for the screen after getting the front glass off.

    mastover - Replica

    I use a similar technique: I print out the iFixit manual for the job, and Scotch-tape down the screws/brackets/cables I remove at each step next to the component descriptions. That way, when I'm reassembling, the bits are taped right next to the photo of where they came from.

    adlerpe -

    That's exactly what I do for all my repairs! It's the best way to keep track of all of the parts ' original location and to make sure that you don't miss any parts during reassembly.

    joyitsjennie -

    Great idea and one I use often

    Thomas Overstreet -

    Excellent idea! Thanks for sharing it here.

    Laura Sharkey -

    I used a 00 that fit but the screws were very tight so I used a tiny paintbrush with some wd40 on it and put it around the edges of the screws. Worked like a charm

    valentinedhdh - Replica

  2. Solleva leggermente il case inferiore e spingilo verso la parte posteriore del computer per liberare le linguette di montaggio.
    • Solleva leggermente il case inferiore e spingilo verso la parte posteriore del computer per liberare le linguette di montaggio.

    In the introduction you should link fixers to this excellent doc: https://www.ifixit.com/Misc/HD_Software_...

    It is really critical, super easy, and free(!) to clone your existing drive onto the new one you will install. I ran into one error, but SuperDuper! support replied immediately on how to fix it...Thanks ifixit and SuperDuper! (I ponied up the $28 for the software anyway, I was so impressed!)

    Mike - Replica

  3. Per precauzione, suggeriamo di scollegare il connettore della batteria dalla scheda logica per evitare eventuali scariche elettriche.
    • Per precauzione, suggeriamo di scollegare il connettore della batteria dalla scheda logica per evitare eventuali scariche elettriche.

    • Mediante l'estremità piatta di uno spudger, sollevare il connettore del cavo della batteria dal connettore femmina sulla scheda logica staccandolo da questa.

    Citazione da gansodesoya:

    why is step 3 necessary?

    Just to disconnect any power source to avoid damages by short-circuits.

    MrKane - Replica

    How do you get that battery connector back on? Do you just press it in back in place after you're done?

    Horace Chung - Replica

    yes. I usually plug it in before I screw it down so I can lift the battery a bit and have enough slack to be able to go straight down on the connector, otherwise it comes in on a bit of an angle, which can't be good (though not necessarily bad).

    maccentric -

    This step almost finished me, and I did extensive damage to the battery plug. Fortunately, I later replaced the battery, and the replacement came with a new plug! :) Newbies need to know - 1. The battery plug is like a thin lip on a thicker lip, so you need to pry BETWEEN 2 thin lips to get it off, else you are trying to yank out the socket. 2. Mine was initially VERY tight, and trying to get it out broke the plastic on all sides of plug, even though I was as careful as possible. Luckily, this didn't hurt functionality and I later replaced the battery. AFTER disconnecting once, it was never so tight again,

    Jeff Diamond - Replica

  4. Rimuovi le due viti con testa a croce che fissano la staffa del disco rigido al case superiore.
    • Rimuovi le due viti con testa a croce che fissano la staffa del disco rigido al case superiore.

    • Queste viti restano nella staffa del disco rigido.

  5. Solleva la staffa di fissaggio fuori dal case superiore.
    • Solleva la staffa di fissaggio fuori dal case superiore.

  6. Solleva il disco rigido dall'apposita linguetta ed estrailo dal case, ricordando che è ancora collegato al computer tramite il cavo.
    • Solleva il disco rigido dall'apposita linguetta ed estrailo dal case, ricordando che è ancora collegato al computer tramite il cavo.

  7. Scollega il cavo del disco rigido estraendolo direttamente dall'unità stessa.
    • Scollega il cavo del disco rigido estraendolo direttamente dall'unità stessa.

    I guess it's probably my fault that I broke the SATA cable during this step (unless the cable was somehow already weakened), but for anyone reading this, be extra careful. My connector was fitted really tightly, and when it finally came out it ripped the cable, which is pretty expensive in its own right (although you can get a cheaper deal on eBay).

    nitrous - Replica

  8. Rimuovi le due viti Torx T6 da ciascun lato del disco rigido, per un totale di quattro viti. Trasferisci queste viti nella nuova unità, se la stai sostituendo.
    • Rimuovi le due viti Torx T6 da ciascun lato del disco rigido, per un totale di quattro viti.

    • Trasferisci queste viti nella nuova unità, se la stai sostituendo.

    • Se stai installando un nuovo hard drive, abbiamo una guida all'installazione di OS X per rimettere rapidamente in uso il tuo MacBook.

    Does anyone know how I can get another set of the T6 screws I took out of my old HD? I forgot to save them and now my new SSD rattles around in the laptop!

    help

    TimAndSusanna Decker - Replica

    Hi there. We sell the Screw Set for the MBP 13" Mid 09 which includes the hard drive T6 screws you require. Hope this helps.

    Walter Galan -

    For those with the boot up issues, did you create a bootable flash drive per this link: Creare una chiavetta USB avviabile

    and THEN follow the install procedure for High Sierra at this link: Come installare MacOS High Sierra

    I didn’t replace my hard drive, but those seem to be crucial steps prior to replacing it.

    This document is also referenced in a comment in one of the earliest steps of this guide. https://s3.amazonaws.com/ifixit-assets/M...

    Dan - Replica

Conclusione

Per rimontare il tuo dispositivo, segui queste istruzioni in ordine inverso.

Altre 499 persone hanno completato questa guida.

Un ringraziamento speciale a questi traduttori:

en it

100%

Claire Rapp ci sta aiutando ad aggiustare il mondo! Vuoi partecipare?
Inizia a tradurre ›

THANK YOU! I'm still on a high from repairing my husband's Macbook. It feels so nice to have two computers up and running again. You saved me nearly a grand, and made me realize how much I really did learn as a kid building PC towers with my dad.

emhannaford - Replica

Hi, I got the 1TB SSD Hybrid you have listed above. Regardless of what I try, my computer does not recognize it. It sees the 32GB flash drive I used for an install disk and it sees my USB external drive where I have the time machine backup. But it just can't see this drive. Is there any troubleshooting for this product? Thanks!

robbyglasco - Replica

Hi Robbyglasco, Have you been able to fix the issue? I'm having the same problem :-)

lkaravis -

I know this is a long time after the event for both of you, but for others Im pretty sure that this will be that you haven't yet formatted the SSD in Disk Utility. Before you can reinstall from Time Machine you have to go into Disk Utility and format the SSD. You get to Disk Utility from the option screen after you have booted the computer with "Command and R" (cmd-R).

Graham Crewe -

Thank you very much. This made the job much easier than it would have been if I had to figure it out for myself.

I replaced a 5 year old 320GB hard drive with a new 1TB hard drive. I first cloned the drive by attaching the new one via a USB dongle and running Carbon Copy Cloner. Then I booted the new drive via USB to confirm that it was properly cloned.

Then I followed the directions here. It took all of 15 minutes to do, because I knew exactly what to expect and had all the necessary tools on-hand. Your web site is an incredibly valuable resource. Thanks again.

David Charlap - Replica

My computer didn't recognize the 500gb seagate at first as a drive to restore onto. I had to add a new name under that in disk utility. Then went back to restore from time machine (external hard drive) and the drive was there with the new name!!

susanmyers - Replica

The HD in my mid2010 Mac was failing. I bought a replacement on eBay, 'Migrated' my files and settings to it after installing Mac OS and then booted from it via USB to check it was working. Relpacing the faulty drive was a doddle thanks to this clear, concise, accurate guide. Go raibh míle maith agat! (Gaelic for 'Thank You!')

aodhagan - Replica

I have tried to replace the hard drive of my MacBook Pro Computer mid 2010 with a Samsung 850 Evo of 500 GB 2.5 inch Solid State Drive. I have been following all the instructions given, but when I have finished and tried to install the system from a pendrive (Mac OS High Sierra) into the computer, and gone to the Disk Utilities for formatting the new SSD disk, NO INTERNAL DISK appears, this is, the new (and only) internal disk is not recognize by the computer.

Could someone help me? Is this a problem of the Samsung 850 Evo (Sata III, I think) with my Computer model? Would I need to change the SSD type or brand to get a full compatibility? Could I have done something wrong during the process?

I will appreciate very much your assistance.

Jose Luis Garcia Garrido

jgarciagarrido@gmail.com

April 28

Jose L Garcia Garrido - Replica

I ran to the same issue before. I isolated the problem as a HDD cable issue. The newer HDD does not have propoer contact with the pins on the HDD.  I tried several HDD. I just purchased and swapped the iternal HDD cable and fixed the issue. Hope this helps your issue.

Hazel Atienza -

I used these instructions to upgrade my mid 2010 15” MBP. Absolutely spot on! Thanks for taking the mystery out of how to make this upgrade. BTW, I installed a Samsung EVO 860 500GB SSD, no cable issue (thank goodness:-).

KenT - Replica

Will I need a spacer for a SSD replacement since it is only 7mm, not 9.5mm, or will the drive bracket hold it firmly in place? Thanks

Pam Dooner - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 16

Ultimi 7 Giorni: 161

Ultimi 30 Giorni: 844

Tutti i Tempi: 588,521