Strumenti

Parti

Nessuna parte richiesta.

  1. Flip the device over so the bottom is facing up.
    • Flip the device over so the bottom is facing up.

    • You will know it is the bottom because there will be six silver screws visible.

    Aggiungi Commento

  2. Remove the USB converter device by gently pulling it out.
    • Remove the USB converter device by gently pulling it out.

    • Do not pull the converter device out by the cord.

    Aggiungi Commento

    • Remove the six silver screws using a small Phillips head screwdriver.

    Aggiungi Commento

    • Slide the bottom plastic panel of the shell down so it is free of the end cap and the top panel.

    • Lift panel free of device.

    Aggiungi Commento

    • Remove the plastic end cap by sliding it forward, freeing from the rest of the device.

    • You can identify the end cap by noting the label "SuperDisk Drive" above where you would insert a floppy disk.

    Aggiungi Commento

    • Slide the metal housing out of the plastic shell.

    Aggiungi Commento

  3. Diffondi allegria Fixmas
    Ottieni $12 sul tuo acquisto di $50 o più con il codice FIXMAS12
    Diffondi allegria Fixmas
    Ottieni $12 sul tuo acquisto di $50 o più con il codice FIXMAS12
    • Slide metal panel out of the metal casing.

    Aggiungi Commento

    • Slide disk drive out of metal casing.

    Aggiungi Commento

    • Flip the disk drive over so the the plug on the daughter board is visible.

    Aggiungi Commento

    • Using an iPod opener put pressure on the white plug and pull backwards until the daughter board unplugs from the main unit.

    Aggiungi Commento

    • Gently pull on the daughter board until it separates from the device.

    Aggiungi Commento

    • Place a plastic spudger in between the disk drive and its metal casing. Use the spudger as a lever the until the metal casing detaches from the disk drive.

    • You may have to use the plastic spudger in several spots along the metal casing.

    Aggiungi Commento

    • lift the disk drive completely out of the metal casing and set it aside.

    Aggiungi Commento

    • Flip the device over so the plastic arm is face up.

    Aggiungi Commento

    • Remove the small spring that connects the plastic arm to the disk drive.

    • To the keep the spring from flying in the air and getting lost, put your finger on one end of the spring to hold it in place while you detach the other end. It does not matter which end you chose to detach first.

    Aggiungi Commento

    • Locate the tab with a raised dot on the immobile end of the plastic arm.

    • Apply pressure on the plastic tab and slide it backwards to release that end of the arm from the disk drive.

    Aggiungi Commento

    • Rotate the plastic arm until it fits through the opening in the disk drive and pull it out.

    • Completely remove the plastic arm from the disk drive.

    • Replace the arm if it is broken or set it aside and continue to your next task.

    Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Brittini

Membro da: 11/02/2014

16 Reputazione

1 Guida realizzata

Team

Ohio State, Team 1-2, Buehl Spring 2014 Membro di Ohio State, Team 1-2, Buehl Spring 2014

OSU-BUEHL-S14S1G2

4 Membri

9 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 3

Tutti i Tempi: 241