Aggiusta la tua roba Comunità Store

Husqvarna FE 350 Rear Sprocket Replacement

Introduzione

If you need to replace the rear sprocket on your Husqvarna FE 350, follow this step by step guide. Be sure that the bike is off prior to beginning this repair. You will need a bike stand to do the repair and potentially a helper to place it on the stand.

Cosa ti serve

  1. Husqvarna FE 350 Rear Sprocket Replacement, Rear Sprocket: passo 1, immagine 1 di 1

    • Place the motorcycle on a stand so that the rear tire is off the ground.

    Modifica

  2. Husqvarna FE 350 Rear Sprocket Replacement: passo 2, immagine 1 di 2 Husqvarna FE 350 Rear Sprocket Replacement: passo 2, immagine 2 di 2

    • Use the 27mm wrench to unscrew the nut that holds the axle together. This nut is located on the right side of the motorcycle at the end of the swing-arm.

    Modifica

  3. Husqvarna FE 350 Rear Sprocket Replacement: passo 3, immagine 1 di 3 Husqvarna FE 350 Rear Sprocket Replacement: passo 3, immagine 2 di 3 Husqvarna FE 350 Rear Sprocket Replacement: passo 3, immagine 3 di 3

    • Move to the left side of the motorcycle and remove the axle by pulling it directly out.

    • Move back to the right side and remove the spacer shown in the third picture to ensure that is does not get lost.

    Modifica

  5. Husqvarna FE 350 Rear Sprocket Replacement: passo 4, immagine 1 di 2 Husqvarna FE 350 Rear Sprocket Replacement: passo 4, immagine 2 di 2

    • Pull up and back on the chain to free the tire.

    Modifica

  6. Husqvarna FE 350 Rear Sprocket Replacement: passo 5, immagine 1 di 1

    • Lay the tire on a flat surface with with sprocket facing up.

    • Use the 6mm Torx wrench to unscrew the six bolts holding the sprocket on.

    • Replace the sprocket and screw the bolts back in.

    Modifica

  7. Husqvarna FE 350 Rear Sprocket Replacement: passo 6, immagine 1 di 1

    • Be careful that the brake rotor fits in between the brake pads on the caliper.

    Modifica

  8. Husqvarna FE 350 Rear Sprocket Replacement: passo 7, immagine 1 di 1

    • Put the chain back on. Start at the bottom and work the chain carefully over the top of the new sprocket.

    Modifica

  9. Husqvarna FE 350 Rear Sprocket Replacement: passo 8, immagine 1 di 3 Husqvarna FE 350 Rear Sprocket Replacement: passo 8, immagine 2 di 3 Husqvarna FE 350 Rear Sprocket Replacement: passo 8, immagine 3 di 3

    • Push the axle back through the swing arm and the wheel.

    • Place the spacer back onto the axle with the square side pointing forward.

    • Thread the 27mm nut back onto the axle.

    Modifica

  10. Husqvarna FE 350 Rear Sprocket Replacement: passo 9, immagine 1 di 1

    • Use the 27mm wrench to tighten the nut down.

    Modifica
Linea Traguardo

Altre 2 persone hanno completato questa guida.

Un commento

C'est bien. je veux apprendre à réparer les motos

Enoch DEMBELE - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 19

Ultimi 30 Giorni: 50

Tutti i Tempi: 971