Salta al contenuto principale

Huawei P10 Lite Motherboard Replacement

Cosa ti serve

  1. Huawei P10 Lite Motherboard Replacement, Back cover: passo 1, immagine 1 di 3 Huawei P10 Lite Motherboard Replacement, Back cover: passo 1, immagine 2 di 3 Huawei P10 Lite Motherboard Replacement, Back cover: passo 1, immagine 3 di 3
    • Insert the tip of an opening pick between the back cover and the mid frame and slide it around the phone, to cut the adhesive.

    • Using a suction handle to lift the back cover may help to get an initial gap for the opening pick to put in.

    • If the adhesive is hard to cut, use an iOpener to loosen it.

    Mit dem Saugnapf die Rückseite anheben hilft ungemein…

    Matthias Eberle - Replica

    Had to use blue wedge tool to wedge open bottom plate from the rim part in order to then use the tip of the blue opening pick under the back plate to then cut the glue. It’s like placing a pie server or knife under the plate once there’s a gap between the rim and the back plate.

    Jane - Replica

    Be careful, there’s a cable to fingerprint sensor, very close to the edge (see pictures below)… It’s very easy to cut it through with the pick, as I just learned :)

    dambig - Replica

  2. Huawei P10 Lite Motherboard Replacement: passo 2, immagine 1 di 3 Huawei P10 Lite Motherboard Replacement: passo 2, immagine 2 di 3 Huawei P10 Lite Motherboard Replacement: passo 2, immagine 3 di 3
    • After you cut the adhesive on every edge, twist your opening pick, to separate the rear cover from the phone.

    • Flip the rear cover over to the right side of the phone.

  3. Huawei P10 Lite Motherboard Replacement: passo 3, immagine 1 di 2 Huawei P10 Lite Motherboard Replacement: passo 3, immagine 2 di 2
    • Use a pair of tweezers to remove the sticker.

    • Remove the two Phillips #00 screws.

    • Remove the four 2.5 mm Phillips #00 screws.

    Schritt 3 und 4 kann man sich komplett sparen. Wozu auch. Kann gleich mit Schritt 5 weitergemacht werden, zuvor einfach das Flachbandkabel vom Fingerabdrucksensor an der Rückabdeckung abklemmen und fertig.

    Bobby mcgee - Replica

    There are four silver screws and two black to be removed.

    Jane - Replica

    Translate what Bobby mcgee said:

    Step 3 and 4 can be completely ignored. What for? You can continue with step 5, just disconnect the ribbon cable from the fingerprint sensor on the back cover and you're done.

    Antonio Sun - Replica

    However, the reason step 3 and 4 should not be skipped is Step 6 — Use an iOpener to loosen the adhesive beneath the battery. I.e., the adhesive cannot be easily removed without heat, however, that heat might damage the electric chips. Thus they’d better be removed first.

    Antonio Sun - Replica

  4. Huawei P10 Lite Motherboard Replacement: passo 4, immagine 1 di 2 Huawei P10 Lite Motherboard Replacement: passo 4, immagine 2 di 2
    • Use tweezers to remove the mainboard shield.

    • Use the flat end of a spudger to disconnect the finger print sensor flex cable.

    • When reassembling apply new adhesive where it is necessary.

    Welchen Klebstoff soll man verwenden?

    josef navratil - Replica

    Hallo Josef,

    sollte bei deinem Ersatzteil kein Klebstoff oder Klebeband dabei gewesen sein, kannst du dünne Streifen Doppelseitiges Klebeband verwenden. Es gibt für das Huawei P10 Lite auch schon zugeschnittene Klebestreifen zu erwerben, hierbei gilt aber je nach Händler Rezessionen zu lesen, ob die Klebestreifen auch wirklich halten.

    Dominik Schnabelrauch -

    Note that there is a copper-colored sticker to lift up near the flat cable connected from the phone the finger pad. Lift the main board plate (shield) up SLOWLY from the camera side to the other end as the plate is wedged in place.

    Jane - Replica

    what adhesive is recommended? thanks

    darren - Replica

    Hi darren,
    pre-cut adhesive would be the best solution if you can source it. Otherwise a two-sided adhesive tape or carefully used E6000 adhesive glue will be your friend.

    Tobias Isakeit -

  5. Huawei P10 Lite Motherboard Replacement, SIM Card Tray: passo 5, immagine 1 di 2 Huawei P10 Lite Motherboard Replacement, SIM Card Tray: passo 5, immagine 2 di 2
    • Use a SIM card removal bit or tool and push it into the small hole in the SIM card tray.

    • Remove the SIM card tray.

  6. Huawei P10 Lite Motherboard Replacement, Motherboard: passo 6, immagine 1 di 3 Huawei P10 Lite Motherboard Replacement, Motherboard: passo 6, immagine 2 di 3 Huawei P10 Lite Motherboard Replacement, Motherboard: passo 6, immagine 3 di 3
    • Remove the three Phillips #000 screws.

    • Use tweezers to remove the two metal shields which cover the flex cables on the mainboard.

  7. Huawei P10 Lite Motherboard Replacement: passo 7, immagine 1 di 3 Huawei P10 Lite Motherboard Replacement: passo 7, immagine 2 di 3 Huawei P10 Lite Motherboard Replacement: passo 7, immagine 3 di 3
    • Use the flat end of a spudger to disconnect the volume and power button, the display and the main flex cable.

  8. Huawei P10 Lite Motherboard Replacement: passo 8, immagine 1 di 2 Huawei P10 Lite Motherboard Replacement: passo 8, immagine 2 di 2
    • Disconnect the battery flex cable with a spudger.

    • Unplug the antenna cable with tweezers.

  9. Huawei P10 Lite Motherboard Replacement: passo 9, immagine 1 di 3 Huawei P10 Lite Motherboard Replacement: passo 9, immagine 2 di 3 Huawei P10 Lite Motherboard Replacement: passo 9, immagine 3 di 3
    • Disconnect the headphone jack flex cable with the flat end of a spudger.

    • Use an opening pick to pry out the motherboard until you can get a good grip.

    • Both camera are still attached to the motherboard. Don't damage them while you remove it.

    • Remove the motherboard.

    • If you want to replace your motherboard you need to disconnect both cameras and transfer them to your spare part.

    • On the back of the motherboard there are thermal pads (pink rubber-like gobs) for heat dissipation. If these thermal pads broke or are too dried out you might need to apply new thermal pads on the new display assembly or the motherboard.

    Clear and to the point. Many thanks…

    Richard Marere - Replica

    Where to buy new motherboard original huawei.

    Neil - Replica

Conclusione

To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.

Altre 8 persone hanno completato questa guida.

Team

iFixit Membro di iFixit

Staff

136 Membri

16.573 Guide realizzate

2 Commenti

ma la scheda di ricambio dove la trovo?

ghisle84 - Replica

I need huawei p10 lite board 4gb 64gb

Fani Malik - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 11

Ultimi 30 Giorni: 57

Tutti i Tempi: 13,038