Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Huawei P10 Lite Headphone Jack Replacement

Introduzione

Use this guide to replace the headphone jack in your Huawei P10 Lite smartphone. When reassembling your phone apply new adhesive where it is necessary.

Cosa ti serve

  1. Huawei P10 Lite Headphone Jack Replacement, Back cover: passo 1, immagine 1 di 3 Huawei P10 Lite Headphone Jack Replacement, Back cover: passo 1, immagine 2 di 3 Huawei P10 Lite Headphone Jack Replacement, Back cover: passo 1, immagine 3 di 3

    • Insert the tip of an opening pick between the back cover and the mid frame and slide it around the phone, to cut the adhesive.

    • Using a suction handle to lift the back cover may help to get an initial gap for the opening pick to put in.

    • If the adhesive is hard to cut, use an iOpener to loosen it.

    Traduci

  2. Huawei P10 Lite Headphone Jack Replacement: passo 2, immagine 1 di 3 Huawei P10 Lite Headphone Jack Replacement: passo 2, immagine 2 di 3 Huawei P10 Lite Headphone Jack Replacement: passo 2, immagine 3 di 3

    • After you cut the adhesive on every edge, twist your opening pick, to separate the rear cover from the phone.

    • Flip the rear cover over to the right side of the phone.

    Traduci

  4. Huawei P10 Lite Headphone Jack Replacement: passo 3, immagine 1 di 2 Huawei P10 Lite Headphone Jack Replacement: passo 3, immagine 2 di 2

    • Use a pair of tweezers to remove the sticker.

    • Remove the two Phillips #00 screws.

    • Remove the four 2.5 mm Phillips #00 screws.

    Traduci

  5. Huawei P10 Lite Headphone Jack Replacement: passo 4, immagine 1 di 2 Huawei P10 Lite Headphone Jack Replacement: passo 4, immagine 2 di 2

    • Use tweezers to remove the mainboard shield.

    • Use the flat end of a spudger to disconnect the finger print sensor flex cable.

    • When reassembling apply new adhesive where it is necessary.

    Traduci

  6. Huawei P10 Lite Headphone Jack Replacement, Battery Disconnection: passo 5, immagine 1 di 3 Huawei P10 Lite Headphone Jack Replacement, Battery Disconnection: passo 5, immagine 2 di 3 Huawei P10 Lite Headphone Jack Replacement, Battery Disconnection: passo 5, immagine 3 di 3

    • Remove the Phillips screw holding the battery connector plate in place.

    • Remove the battery connector plate.

    • Use the flat end of a spudger to disconnect the battery flex cable.

    Traduci

  7. Huawei P10 Lite Headphone Jack Replacement, Headphone Jack: passo 6, immagine 1 di 2 Huawei P10 Lite Headphone Jack Replacement, Headphone Jack: passo 6, immagine 2 di 2

    • Use the flat end of a spuder to disconnect the headphone jack flex cable.

    • Altough the headphone jack is not glued to the mid frame it is a little bit tucked in its bracket. Be careful not to damage it during the removal.

    • Remove the headphone jack.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order. When reassembling your phone apply new adhesive where it is necessary.

Altre 2 persone hanno completato questa guida.

Autore

con 1 altro collaboratore

Dominik Schnabelrauch

Membro da: 11/23/16

203.353 Reputazione

682 Guide realizzate

Distintivi: 40

+37 altri distintivi

Team

iFixit Membro di iFixit

Staff

135 Membri

16.817 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 2

Tutti i Tempi: 3,348