Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Store

Introduzione

Use this guide to replace the display of your Huawei Mate 9 smartphone.

  1. First switch off your phone and remove the SIM card tray. First switch off your phone and remove the SIM card tray.
    • First switch off your phone and remove the SIM card tray.

  2. Remove both screws on the bottom with a Torx T2 screwdriver. Use a plastic opening tool to get between the display and the case. Open the smartphone by carefully prying out the display with all the parts out of the case.
    • Remove both screws on the bottom with a Torx T2 screwdriver.

    • Use a plastic opening tool to get between the display and the case. Open the smartphone by carefully prying out the display with all the parts out of the case.

    • Don't open the phone all the way, yet. The fingerprint sensor cable is still connected to the back cover.

  3. Swing open the phone to the right side. Disconnect the fingerprint sensor cable with a spudger.
    • Swing open the phone to the right side.

    • Disconnect the fingerprint sensor cable with a spudger.

  4. Carefully peel off the plastic sticker that holds both cables to the battery.
    • Carefully peel off the plastic sticker that holds both cables to the battery.

  5. Remove the water indicator sticker and the Phillips #00 screw beneath it, that holds the cable bracket in its place.
    • Remove the water indicator sticker and the Phillips #00 screw beneath it, that holds the cable bracket in its place.

  6. SKIP THE UPGRADE

    Save by fixing with an all-in-one kit.

    Shop iPhone Fix Kits

    SKIP THE UPGRADE

    Save by fixing with an all-in-one kit.

    Shop iPhone Fix Kits
  7. Remove the cable bracket.
    • Remove the cable bracket.

  8. Use a spudger to disconnect the interconnect, the battery and the display flex cable. Use a spudger to disconnect the interconnect, the battery and the display flex cable. Use a spudger to disconnect the interconnect, the battery and the display flex cable.
    • Use a spudger to disconnect the interconnect, the battery and the display flex cable.

  9. It's not required to remove the battery  in order to remove the display of the Huawei Mate 9. Disconnect the antenna cable and remove it carefully. Remove the five Phillips #00 screws that hold the daughter board and loudspeaker in its place.
    • It's not required to remove the battery in order to remove the display of the Huawei Mate 9.

    • Disconnect the antenna cable and remove it carefully.

    • Remove the five Phillips #00 screws that hold the daughter board and loudspeaker in its place.

  10. Remove the metal shield that covers the connection of the motherboard flex cable. Use a spudger to unplug the motherboard flex cable and remove it.
    • Remove the metal shield that covers the connection of the motherboard flex cable.

    • Use a spudger to unplug the motherboard flex cable and remove it.

  11. Use a spudger to disconnect the loudspeaker and the charging port flex cable from the daughterboard. Use a spudger to disconnect the loudspeaker and the charging port flex cable from the daughterboard.
    • Use a spudger to disconnect the loudspeaker and the charging port flex cable from the daughterboard.

  12. Use a spudger to carefully lever up the daughterboard and remove it. Don't break the small clamps that hold down the daughter board but press them a little bit to the side to make the removal easier. Use a spudger to remove the loudspeaker and the charging port. There is some adhesive underneath and the unit might be a little bit sticky. If you're having a hard time while removing the loudspeaker  you can use an iOpener to loosen the adhesive and try it again.
    • Use a spudger to carefully lever up the daughterboard and remove it. Don't break the small clamps that hold down the daughter board but press them a little bit to the side to make the removal easier.

    • Use a spudger to remove the loudspeaker and the charging port. There is some adhesive underneath and the unit might be a little bit sticky.

    • If you're having a hard time while removing the loudspeaker you can use an iOpener to loosen the adhesive and try it again.

  13. Use an iOpener to loosen the adhesive beneath the display.  Focus on the top and bottom area of it. After loosening the adhesive in the upper area of your phone, use an iFlex or opening pick and insert it carefully between the mid frame and your display. Do not insert the tool more than approximately 1/16 of an inch on the sides.
    • Use an iOpener to loosen the adhesive beneath the display. Focus on the top and bottom area of it.

    • After loosening the adhesive in the upper area of your phone, use an iFlex or opening pick and insert it carefully between the mid frame and your display.

    • Do not insert the tool more than approximately 1/16 of an inch on the sides.

    • Loosen the adhesive by sliding the along the mid frame.

  14. Then carefully slide around the whole mid frame. If you're having a hard time while loosening the adhesive beneath the display you can reuse the iOpener and try it again. After you loosened all the adhesive, start to slowly lift up the display from the bottom of your phone.
    • Then carefully slide around the whole mid frame.

    • If you're having a hard time while loosening the adhesive beneath the display you can reuse the iOpener and try it again.

    • After you loosened all the adhesive, start to slowly lift up the display from the bottom of your phone.

  15. To completely remove the display you need to thread the flex cable through the gap in the mid frame. When reassembling your phone apply new adhesive where it is necessary.
    • To completely remove the display you need to thread the flex cable through the gap in the mid frame.

    • When reassembling your phone apply new adhesive where it is necessary.

Conclusione

To reassemble your device, follow these instructions in reverse order. When reassembling apply new adhesive where it is necessary.

Altre 10 persone hanno completato questa guida.

Dominik Schnabelrauch

Membro da: 23/11/2016

71.072 Reputazione

320 Guide realizzate

Team

iFixit Membro di iFixit

Community

128 Membri

12.980 Guide realizzate

I have issue with the assembly process. Im adding 3m adhesive tape that I received with replacement screen, and everything looks fine. But after inserting phone into aluminium back the screen pop out int the middle of frame, delaminating and showing backlight of lcd. The adhesive just not hold it enough..

gingerboi66 - Replica

The iFlex isn’t listed in the tools.

Sean Hannold - Replica

Check, now it is listed. Thanks for the note.

Tobias Isakeit -

it’s almost impossible to remove the battery without damaging it!

My advice to you is to buy the LCD screen with the battery included.

madani_salar - Replica

Hello,

do i have to remove the battery to change the display? That means is the removing of the battery absolutely necessary?

Greetings,

Mark

Mark D. - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 6

Ultimi 7 Giorni: 51

Ultimi 30 Giorni: 230

Tutti i Tempi: 13,551