Aggiusta la tua roba Unisciti alla community Store

How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822

Introduzione

Sometimes the moving about of computer speakers leads to broken wires and the speakers will fail to work properly. This guide will show you how to repair a Harman Kardon CN-04N567-48220 external computer speaker.

Cosa ti serve

  1. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822, How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 1, immagine 1 di 3 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822, How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 1, immagine 2 di 3 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822, How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 1, immagine 3 di 3

    • Use your fingers to pull the top of the speaker grill away from the speaker enclosure.

    • Pull the bottom of the grill away from the speaker enclosure and then completely remove the grill.

    • Four posts attach the grill assembly to the front of speaker enclosure. These posts are located on the back side of the grill assembly.

    Modifica

  2. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 2, immagine 1 di 2 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 2, immagine 2 di 2

    • Remove the top two 9.5 mm Phillips #1 screws from the speaker.

    • Remove the two 9.5 mm Phillips #1 screws located below the speaker screws.

    • Slowly work your way around the seam until the two parts of the enclosure are free.

    • More speaker cable slack may be achieved by pulling additional cable through the rear of the case.

    Modifica

  3. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 3, immagine 1 di 2 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 3, immagine 2 di 2

    • Inspect both sides of the printed circuit board (PCB) for any raised traces, off-colored areas, or loose components.

    • This step is to avoid making a mechanical repair (re-soldering the wires to the PCB) on a piece of equipment that also has obvious electrical or mechanical issues.

    Modifica

  5. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 4, immagine 1 di 1

    • Use desoldering braid and a soldering iron to wick away the old solder and wire remnants from the solder pads and through-holes.

    • Do not leave solder bridges across the pads as this will cause functional issues.

    Modifica

  6. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 5, immagine 1 di 2 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 5, immagine 2 di 2

    • Use wire strippers to remove a small section of insulation from the wires.

    • Use a soldering iron and solder to tin the wires. This prevents the strands from fraying.

    Modifica

  7. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 6, immagine 1 di 2 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 6, immagine 2 di 2

    • Insert the yellow wire into the through-hole marked "R".

    • Insert the bare ground wire into the through-hole marked "G".

    • Insert the white wire into the through-hole marked "L".

    Modifica

  8. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 7, immagine 1 di 1

    • Use the soldering iron to flow solder between each wire and its solder pad.

    Modifica

  9. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 8, immagine 1 di 1

    • Reassemble the two parts of the enclosure making sure that the PCB-mounted audio jacks are lined up with the mating holes of the rear enclosure.

    • Route the cable inside the enclosure to avoid stressing the solder joints.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 7 persone hanno completato questa guida.

Autore

con 2 altri collaboratori

Ken Gage

Membro da: 06/09/16

285 Reputazione

1 Guida realizzata

Distintivi: 6

+3 altri distintivi

Team

Texas Tech, Team 3-1, Rauch SU 2016 Membro di Texas Tech, Team 3-1, Rauch SU 2016

TTU-RAUCH-SU16S3G1

2 Membri

2 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 14

Ultimi 30 Giorni: 57

Tutti i Tempi: 3,975