Menü

Le tue impostazioni

Il mio banco da lavoro

Ottieni un rapido accesso alle guide, ai componenti e alle risposte per i tuoi dispositivi
Il Mio Carrello

Sembra che il tuo carrello sia vuoto

Sfoglia il Nostro Negozio

HTC myTouch 3G Glass Screen/LED Display Replacement

Scritto Da: Tony Tran (e 4 altri collaboratori)
  • Commenti: 0
  • Preferiti: 4

Difficoltà

Facile

Passi

12

Tempo Necessario

15 - 20 minuti

Sezioni

2

Contrassegni

7

Grammar Police

Vigilanza sulla Grammatica

Adotta il tuo insegnante di inglese interno e contribuisci a migliorare la grammatica di questa guida!

Confusing Text

Testo Confuso

Parte del testo di questa guida è confusionario, doppio, o fuori tema. Modificarlo per renderlo più chiaro!

Incorrect Tools

Attrezzi Non Corretti

Contribuisci a rendere migliore questa guida usando i giusti strumenti nelle immagini e/o nel testo.

Slice and Dice

Fallo a Fettine

I passaggi in questa guida dovrebbero essere suddivisi e trasformati in una serie di guide prerequisite.

Action Shots

Foto Azione

Passa all'azione, eroe! Questa guida ha bisogno di immagini che meglio illustrano come eseguire azioni specifiche.

Markup Mishap

Inconveniente Markup

Questa guida ha bisogno di markup migliori. Contribuisci correggendoli o con annotazioni sui markup.

Better Introduction

Introduzione Migliore

Migliora questa guida completando o revisionando la sua introduzione.

Strumenti

Acquista questi strumenti

Parti

  1. Press each thumb on both sides of the upper corners and apply pressure downwards. Then, while still applying pressure, slide the back cover down.

    • Press each thumb on both sides of the upper corners and apply pressure downwards.

    • Then, while still applying pressure, slide the back cover down.

    Modifica

  2. Remove the Battery. Remove the SIM card.

    • Remove the Battery.

    • Remove the SIM card.

    Modifica

  3. Push the SD card in and the SD card should pop loose.

    • Push the SD card in and the SD card should pop loose.

    • Pull the SD card out.

    Modifica

  4. Remove the four 6-mm T5 torx screws in the four corners. Remove the two 4-mm T5 torx screws in the middle.

    • Remove the four 6-mm T5 torx screws in the four corners.

    • Remove the two 4-mm T5 torx screws in the middle.

    Modifica

  5. Kit riparazione batterie MacBook

    A partire da $69.99

    Buy Now

    Kit riparazione batterie MacBook

    A partire da $69.99

    Buy Now

  6. Use the existing gap, to dislodge the antenna cover from the phone. Pull out the antenna cover to have access to the motherboard.

    • Use the existing gap, to dislodge the antenna cover from the phone.

    • Pull out the antenna cover to have access to the motherboard.

    Modifica

  7. Use a precision flathead screwdriver to dislodge the back plate from the phone by carefully inserting it into the slit between the frame and cover and pushing downward. Go around the edges of the phone, and continue to dislodge the back plate from the front part of the phone.

    • Use a precision flathead screwdriver to dislodge the back plate from the phone by carefully inserting it into the slit between the frame and cover and pushing downward.

    • Go around the edges of the phone, and continue to dislodge the back plate from the front part of the phone.

    Modifica

  8. Remove the 3-mm Phillips head screw located on the side of the bottom left-hand corner of the phone. Remove the 3-mm Phillips head screw located on the top right-hand corner of the phone.

    • Remove the 3-mm Phillips head screw located on the side of the bottom left-hand corner of the phone.

    • Remove the 3-mm Phillips head screw located on the top right-hand corner of the phone.

    • Do not remove any of the screws located on the actual circuit boards.

    Modifica

  9. Place a finger between the circuit board and the front cover, and lift up gently. Continue separating the circuit board from the front cover and screen and watch for a ribbon cable to detach. Finish separating the circuit board from the front panel.

    • Place a finger between the circuit board and the front cover, and lift up gently.

    • Continue separating the circuit board from the front cover and screen and watch for a ribbon cable to detach.

    • Finish separating the circuit board from the front panel.

    Modifica

  10. After following the prerequisite guide listed above, the phone should have the circuit board housing group on one piece.

    • After following the prerequisite guide listed above, the phone should have the circuit board housing group on one piece.

    • The front cover and screen of the phone should be located on the other piece.

    Modifica

  11. Place a finger on the front side of the screen, and push up as indicated. Carefully grab onto the sides of the LCD and glass screen.

    • Place a finger on the front side of the screen, and push up as indicated.

    • Carefully grab onto the sides of the LCD and glass screen.

    • Continue to angle the LCD and glass screen further up.

    Modifica

  12. Carefully lift the screen away from the front cover.

    • Carefully lift the screen away from the front cover.

    • The adhesive should be easy to separate while separating the front cover from the screen.

    Modifica

  13. Change old LCD and glass digitizer with a replacement.

    • Change old LCD and glass digitizer with a replacement.

    • The LCD and glass digitizer can be separated by disconnecting the ribbon cable, and separating the layer of the LCD from the glass screen.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 4 altri collaboratori

Tony Tran

Membro da: 25/09/2012

366 Reputazione

3 Guide realizzate

Distintivi: 9

+6 altri distintivi

Team

Cal Poly, Team 2-9, Propen Fall 2012 Membro di Cal Poly, Team 2-9, Propen Fall 2012

CPSU-PROPEN-F12S2G9

3 Membri

5 Guide realizzate

0 Commenti

Aggiungi un commento

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 2,740