Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn over the Vive controller so that the bottom saucer is facing up.
-
Use the T5 Torx screwdriver to remove three black 21mm screws from the bottom saucer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the nylon spudger to separate the top and bottom saucer covers all around the edges.
-
Remove only the top saucer cover by pulling up with your hand.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the Phillips 00 screwdriver to remove the three silver 12.8mm screws from the exposed upper sensor panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully pull away the bottom saucer cover with your hand.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the T5 Torx screwdriver to remove the two black 5.2mm screws on the back gray panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn over the Vive controller so that the exposed bottom saucer panel is facing up.
-
Use the T5 Torx screwdriver to remove the three black 5.2mm screws.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the nylon spudger to separate the front panel gently by running the spudger around the edges of the handle.
-
Gently lift the right side of the panel to the left.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the upper ribbon cable gently by pulling the ribbon up and away from the motherboard with two fingers.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the middle ribbon cable gently by pulling the ribbon cable up and away from the motherboard with two fingers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the nylon spudger to lift the white tab by 90 degrees.
-
Disconnect the bottom ribbon cable gently by pulling the ribbon cable down with two fingers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the Phillips 00 screwdriver to remove two black 2.8mm screws from the silver plate.
-
Use the Phillips 00 screwdriver to remove the black 5.8mm screw from the bottom right corner of the silver plate.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the silver plate by pinching it with two fingers and lifting up.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the Phillips 00 screwdriver to remove the black 5.8mm screw from the top left of the battery frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the T5 Torx screwdriver to remove the two silver 4.2mm screws from the bottom of the battery frame.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the three-pin cable gently by pinching the cable with two fingers and pulling up.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the battery frame to remove the battery from the Vive controller
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the Phillips 00 screwdriver to remove the two black 5.8mm screws from the top of the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the T5 Torx screwdriver to remove the two silver 4.2mm screws from the bottom of the motherboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the nylon spudger to rotate the black tab up by 90 degrees.
-
Disconnect the ribbon cable carefully with your finger.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the motherboard up and out of the Vive controller using your hands.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the T5 Torx screwdriver to remove the four black 5.2mm screws from the inner part of the trigger.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Push the trigger button in with your finger until it pops out of the front panel.
-
Annulla: non ho completato questa guida.
Altre 6 persone hanno completato questa guida.
Un commento
It is possible to access and replace the trigger without having to disconnect any of the cables. I have done this with 3 controllers already.
Just ignore the steps saying to disconnect the cable, move parts to the side and be careful.