Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn over the Vive controller so that the bottom saucer is facing up.
-
Use the T5 Torx screwdriver to remove three black 21mm screws from the bottom saucer.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the nylon spudger to separate the top and bottom saucer covers all around the edges.
-
Remove only the top saucer cover by pulling up with your hand.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the Phillips 00 screwdriver to remove the three silver 12.8mm screws from the exposed upper sensor panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully pull away the bottom saucer cover with your hand.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the T5 Torx screwdriver to remove the two black 5.2mm screws on the back gray panel.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn over the Vive controller so that the exposed bottom saucer panel is facing up.
-
Use the T5 Torx screwdriver to remove the three black 5.2mm screws.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the nylon spudger to separate the front panel gently by running the spudger around the edges of the handle.
-
Gently lift the right side of the panel to the left.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the upper ribbon cable gently by pulling the ribbon up and away from the motherboard with two fingers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Disconnect the middle ribbon cable gently by pulling the ribbon cable up and away from the motherboard with two fingers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the nylon spudger to lift the white tab by 90 degrees.
-
Disconnect the bottom ribbon cable gently by pulling the ribbon cable down with two fingers.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the T5 Torx head screwdriver to remove the two silver 4.2mm screws from the rear portion of the trackpad.
-
Lift the trackpad up and out of the panel using your hand.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the spudger and place it in the groove that lies between the trackpad and its rear cover.
-
Pry open the rear panel by rotating the spudger clockwise, revealing the daughter board inside the trackpad.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Separate the rear cover from the daughter board using your hands.
-
Be mindful of this tiny ribbon cable when reassembling with a working daughter board. It attaches to the larger ribbon cable, and it will break off if the larger cable is pulled away from the vibration motor.
-
Annulla: non ho completato questa guida.
Altre 14 persone hanno completato questa guida.
4 Commenti
Hey, I just noticed this, but was the ribbon cable going to the haptic motor ripped? If you look at picture 1 of the step 11, there’s a small broken ribbon cable coming out of the haptic motor. You can see it again poking out in both pictures of Step 13. I just want to know if the haptic motor still works on this particular controller.
thanks for the clear detailed disassembly steps, as a tip maybe highlight the haptic motor/speaker, had to replace the broken ribon-cable on 1 of my controllers, i used an old 80 pin ide cable a it is small enough that it can be routed trough the side of the shielding