Aggiusta la tua roba

Diritto alla Riparazione

Componenti & Strumenti

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

HTC Desire 610 Battery Replacement

Scritto Da: Alex Martin (e 2 altri collaboratori)
  • Commenti: 2
  • Preferiti: 4
  • Completamenti: 6

Difficoltà

Facile

Passi

8

Tempo Necessario

15 minuti

Sezioni

1

Contrassegni

0

Introduzione

Is your HTC Desire 610 not holding a charge? Instead of taking it to your phone provider, follow these steps and you can replace that old battery in no time! It's as simple as: take off the back, unscrew the circuit cover, pry out the old battery, and put in a new one. Ta-dah!

  1. Open the SD card slot.

    • Open the SD card slot.

    Traduci

  2. Using plastic opening or prying tool, take off the back cover of the phone. The SD slot opens an area where the edge of the back is exposed and can be pried open easily. The SD slot opens an area where the edge of the back is exposed and can be pried open easily.

    • Using plastic opening or prying tool, take off the back cover of the phone.

    • The SD slot opens an area where the edge of the back is exposed and can be pried open easily.

    Traduci

  3. Using Phillips 000 Screwdriver, remove the two 2.5mm phillips head screws.

    • Using Phillips 000 Screwdriver, remove the two 2.5mm phillips head screws.

    Traduci

  4. Kit per Nintendo Switch

    A quick fix to get back in the game

    Shop Switch Kits

    Kit per Nintendo Switch

    A quick fix to get back in the game

    Shop Switch Kits

  5. Using Torx T5 screwdriver, remove the four silver 5mm torx head screws.

    • Using Torx T5 screwdriver, remove the four silver 5mm torx head screws.

    Traduci

  6. Using Torx T5 bit size, remove the four black 4mm torx screws

    • Using Torx T5 bit size, remove the four black 4mm torx screws

    Traduci

  7. Using plastic opening or prying tool, remove the black plastic circuit cover. Using plastic opening or prying tool, remove the black plastic circuit cover.

    • Using plastic opening or prying tool, remove the black plastic circuit cover.

    Traduci

  8. Using small plastic opening tool, disconnect the wire connection. Do this by carefully inserting tool under wires and pulling straight up. You may need to pry from both sides of the wires to remove the connection.

    • Using small plastic opening tool, disconnect the wire connection. Do this by carefully inserting tool under wires and pulling straight up.

    • You may need to pry from both sides of the wires to remove the connection.

    • Be careful! Damaging the connection port could prevent a new battery from working.

    • When inserting a new battery, press firmly on the white connector to snap it into it's port.

    Traduci

  9. Use the plastic opening tool - you can use a larger one, or keep using the small one - to pry out the battery. The battery is glued in with adhesive, so you may have to pry a little hard. The battery is glued in with adhesive, so you may have to pry a little hard.

    • Use the plastic opening tool - you can use a larger one, or keep using the small one - to pry out the battery.

    • The battery is glued in with adhesive, so you may have to pry a little hard.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 6 persone hanno completato questa guida.

2 Commenti

Aggiungi un commento

Well done! I allways repair iphones, but my own phone is this HTC Desire 610 and I hadn't T5 torx for disassemble it. ;)

voneout - Replica

Hi thanks for the useful video, however after changing it the new battery didnt work. I tried charging and turning on. I replaced with the old one which still charged and was usable but this then also didnt work. Ive checked connections etc. Any other suggestions? Many thanks

simon - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 12

Ultimi 30 Giorni: 52

Tutti i Tempi: 10,844