Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

HP Slate 7 Extreme 4400US Charging port and Audio Jack Circuit Board Replacement

Introduzione

This guide will require caution when connection replacing, due to the strip being easily ripped.

Cosa ti serve

  1. HP Slate 7 Extreme 4400US Charging port and Audio Jack Circuit Board Replacement, Back Cover: passo 1, immagine 1 di 3 HP Slate 7 Extreme 4400US Charging port and Audio Jack Circuit Board Replacement, Back Cover: passo 1, immagine 2 di 3 HP Slate 7 Extreme 4400US Charging port and Audio Jack Circuit Board Replacement, Back Cover: passo 1, immagine 3 di 3

    • Use the plastic opening tool to separate the back cover from the tablet. Carefully use the tool to pry open the sides, going around the entire tablet to lift the sides up.

    • Once all sides have been pried up, pull the cover off and place it to the side.

    Traduci

  2. HP Slate 7 Extreme 4400US Charging port and Audio Jack Circuit Board Replacement, Charging port and Audio Jack Circuit Board: passo 2, immagine 1 di 2 HP Slate 7 Extreme 4400US Charging port and Audio Jack Circuit Board Replacement, Charging port and Audio Jack Circuit Board: passo 2, immagine 2 di 2

    • Use the PH #000 phillips head screw driver to remove one 5.0 mm screw.

    • Move plastic housing and rear facing camera to expose silver bracket.

    Traduci

  4. HP Slate 7 Extreme 4400US Charging port and Audio Jack Circuit Board Replacement: passo 3, immagine 1 di 2 HP Slate 7 Extreme 4400US Charging port and Audio Jack Circuit Board Replacement: passo 3, immagine 2 di 2

    • Use the PH #000 phillips head screw driver to remove three 3.0mm screws. Remove the silver bracket.

    Traduci

  5. HP Slate 7 Extreme 4400US Charging port and Audio Jack Circuit Board Replacement: passo 4, immagine 1 di 3 HP Slate 7 Extreme 4400US Charging port and Audio Jack Circuit Board Replacement: passo 4, immagine 2 di 3 HP Slate 7 Extreme 4400US Charging port and Audio Jack Circuit Board Replacement: passo 4, immagine 3 di 3

    • Use the nylon spudger to flip up the black retaining flap of the zero insertion force (ZIF) connector holding the strip in place.

    • Grab the green circuit board and pull directly up to separate the glued down power strip.

    • Gently pull the circuit board out of its connector.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Autore

con 5 altri collaboratori

Brandon Ko

Membro da: 09/15/16

698 Reputazione

6 Guide realizzate

Distintivi: 9

+6 altri distintivi

Team

USF Tampa, Team 11-4, Blackwell Fall 2016 Membro di USF Tampa, Team 11-4, Blackwell Fall 2016

USFT-BLACKWELL-F16S11G4

4 Membri

16 Guide realizzate

5 Commenti

where can i get the part at?

cat jones - Replica

Where do you even get the part at??

Mountiansurfer Gaming - Replica

Where do I even get the part at???

Mountiansurfer Gaming - Replica

Can you let us know where to get the replacement part from?

ypk77 - Replica

This is completely useless information without a source for the shoddy HP part!

Brian Burke - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 3

Tutti i Tempi: 1,985