Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Make sure that your device is properly shut down and unplugged from any outlet.
-
Flip Pavilion over so that the bottom faces up and locate the battery in the bottom left corner.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Press and slide up the battery release tab with your thumb until the battery pops out of place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using two fingers, pry the rest of the battery out of the socket.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using a Phillips #0 screwdriver, unscrew all four Phillips PM 2.5X13.0mm screws and place in a secure area until the end of the project.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Flip laptop back over and open as far as it can go.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the flat edge of the plastic spudger inserted under the bottom of the strip cover and pry upwards to un-clip the cover, starting at the right and moving to the left.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use hands to completely lift off the strip cover and remove.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the Phillips #0 screwdriver again, unscrew all four Phillips PM 2.5X13.0mm screws from the top of the keyboard and set aside.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using your hands, lift the keyboard up from the top towards yourself until the keyboard is resting in your hand.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Gently slide out the connecting cable from the laptop to the keyboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Completely remove the keyboard from the rest of the laptop.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Flip the Pavilion back over on its backside.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the same Phillips #0 screwdriver, unscrew the six Phillips PM 2.5X6.0mm screws.
-
Also remove the four Phillips PM 2.5X13.0mm screws to remove the thermal plate with the same screwdriver.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Flip the laptop back over and open the lid all the way.
-
Using the flat edge of the plastic spudger, pry straight up to remove the Mini PCI Connector Cables from the board.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Using the tweezers, gently squeeze and pull backwards on the display cable until it is disconnected.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the Phillips #0 screwdriver again to remove the four Phillips 2.5X13.0mm screws that hold the clips for the screen into place.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the laptop around until the top cover is facing you. Keep the laptop in an open position.
-
Unscrew the four Phillips PM 2.5X6.0mm screws using the Phillips #0 that hold the clips of the screen on to the base.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Firmly grasp the top of the screen with your hands and pull towards you and upwards to remove the screen from the base.
-
Annulla: non ho completato questa guida.
Altre 2 persone hanno completato questa guida.