Salta al contenuto principale

HP Pavilion dv9000 Hard Drive Replacement

Cosa ti serve

  1. HP Pavilion dv9000 Hard Drive Replacement, Battery: passo 1, immagine 1 di 1
    • Turn the laptop over to expose the bottom side.

    • Locate the battery removal switch next to the battery compartment

    • Important: Before doing any repairs on the laptop, make sure it is completely powered down and unplugged.

  2. HP Pavilion dv9000 Hard Drive Replacement, Battery Removal: passo 2, immagine 1 di 2 HP Pavilion dv9000 Hard Drive Replacement, Battery Removal: passo 2, immagine 2 di 2
    • Slide the switch all the way to the left to release the battery. The battery should pop up.

    • Lift the battery out.

  3. HP Pavilion dv9000 Hard Drive Replacement, Hard Drive: passo 3, immagine 1 di 1
    • There are two hard drive bays.

    • Hard drive bay 1 is in the lower right corner.

    • Hard drive bay 2 is in the lower left corner.

  4. HP Pavilion dv9000 Hard Drive Replacement: passo 4, immagine 1 di 2 HP Pavilion dv9000 Hard Drive Replacement: passo 4, immagine 2 di 2
    • To remove hard drive 1 from bay 1

    • Using a Phillips #1 screwdriver, remove the two 5 mm screws that hold the bay 1 cover in place.

    • The screws should remain in the cover.

  5. HP Pavilion dv9000 Hard Drive Replacement: passo 5, immagine 1 di 2 HP Pavilion dv9000 Hard Drive Replacement: passo 5, immagine 2 di 2
    • After removing the two cover screws, lift and slide the cover out of position to access the hard drive.

    • Grab the clear plastic pull tab on top of the hard drive to lift the hard drive from the laptop.

  6. HP Pavilion dv9000 Hard Drive Replacement: passo 6, immagine 1 di 3 HP Pavilion dv9000 Hard Drive Replacement: passo 6, immagine 2 di 3 HP Pavilion dv9000 Hard Drive Replacement: passo 6, immagine 3 di 3
    • To remove hard drive 2 from bay 2.

    • Most laptops don't have a second hard drive. If yours does not, then proceed to the next step.

    • Using a Phillips #1 screwdriver remove the two 5 mm screws that hold the bay 2 cover in place.

    • After removing the two cover screws, lift and slide the cover out of position to access the hard drive.

    • Grab the clear plastic pull tab on top of the hard drive, and lift the hard drive from the laptop.

  7. HP Pavilion dv9000 Hard Drive Replacement: passo 7, immagine 1 di 3 HP Pavilion dv9000 Hard Drive Replacement: passo 7, immagine 2 di 3 HP Pavilion dv9000 Hard Drive Replacement: passo 7, immagine 3 di 3
    • After the hard drive has been removed from the laptop, it must then be removed from its bracket.

    • Start by gently pulling the HP hard drive adapter from the end of the hard drive.

    • Using a Phillips #1 screwdriver, remove the four 3 mm bracketing screws on both sides of the hard drive bracket (2 per side) .

    • Lift the hard drive from its metal bracket.

    • Be careful not to touch the green underside as this may damage the hard drive.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 7 persone hanno completato questa guida.

Robby Cabri

Membro da: 01/23/14

172 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 10-32, Maness Winter 2014 Membro di Cal Poly, Team 10-32, Maness Winter 2014

CPSU-MANESS-W14S10G32

4 Membri

6 Guide realizzate

4 Commenti

Hello. In step 7 of the above, what is the name/part number/ size etc of the adapter/connector please ? I need one urgently.

Thanks.

freeflyshannon - Replica

yes that would be very helpfull because the new SSdrive I have will not fit even though is is the same size. I think I need some sort of an adaptor as you say.

Stephen Cox - Replica

For modern SATA SSDs, the typical form factor is 7.5mm. The standard for laptop HDDs is 9.5mm. You will need to buy a plastic spacer in order to properly mount the drive inside your computer.

Michael - Replica

thanks for the help

Stephen Cox - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 4

Ultimi 30 Giorni: 25

Tutti i Tempi: 8,916