Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

HP Pavilion 11-n010dx Fan Replacement

Introduzione

This guide will instruct a user on how to remove the fan in order to replace a potentially faulty piece of hardware. Be sure the device is turned off and disconnected from all power sources.

Cosa ti serve

  1. HP Pavilion 11-n010dx Fan Replacement, Battery: passo 1, immagine 1 di 2 HP Pavilion 11-n010dx Fan Replacement, Battery: passo 1, immagine 2 di 2

    • Use the nylon spudger to remove the rubber pads near the hinge of the screen, then remove the screws under the pads.

    • Use the Phillips #0 to remove four 9mm screws.

    • Use the Phillips #0 to remove seven 6mm screws.

    Traduci

  2. HP Pavilion 11-n010dx Fan Replacement: passo 2, immagine 1 di 3 HP Pavilion 11-n010dx Fan Replacement: passo 2, immagine 2 di 3 HP Pavilion 11-n010dx Fan Replacement: passo 2, immagine 3 di 3

    • Use the nylon spudger to pry the back casing near the hinges for the screen.

    • Continue to pry along the edge of the back case until the back is ready to be removed.

    • Careful when beginning to remove the case. There is a cable attached between the bottom case and the motherboard that must be properly disconnected.

    Traduci

  3. HP Pavilion 11-n010dx Fan Replacement: passo 3, immagine 1 di 2 HP Pavilion 11-n010dx Fan Replacement: passo 3, immagine 2 di 2

    • Use the blue plastic opening tool to lift up on the white tab that is holding the cable in place on the motherboard.

    • Now carefully pull the cable out of place and remove the entire back casing.

    Traduci

  5. HP Pavilion 11-n010dx Fan Replacement: passo 4, immagine 1 di 1

    • Remove the five 6mm screws that hold the battery in place using the Phillips #0.

    Traduci

  6. HP Pavilion 11-n010dx Fan Replacement: passo 5, immagine 1 di 2 HP Pavilion 11-n010dx Fan Replacement: passo 5, immagine 2 di 2

    • Use the nylon spudger to pry away the blue/white wire that is positioned near your battery.

    Traduci

  7. HP Pavilion 11-n010dx Fan Replacement: passo 6, immagine 1 di 2 HP Pavilion 11-n010dx Fan Replacement: passo 6, immagine 2 di 2

    • Disconnect the battery cable from the motherboard by carefully pulling on the black wire at the point closest to the white tab.

    Traduci

  8. HP Pavilion 11-n010dx Fan Replacement: passo 7, immagine 1 di 1

    • Remove the battery from your device.

    Traduci

  9. HP Pavilion 11-n010dx Fan Replacement, Fan: passo 8, immagine 1 di 1

    • Use the Phillips #0 to remove the two 3mm screws holding the fan in place.

    Traduci

  10. HP Pavilion 11-n010dx Fan Replacement: passo 9, immagine 1 di 3 HP Pavilion 11-n010dx Fan Replacement: passo 9, immagine 2 di 3 HP Pavilion 11-n010dx Fan Replacement: passo 9, immagine 3 di 3

    • Use the plastic opening tool to slowly loosen the connection cable.

    • Once the connector is loose enough, grab the cable and carefully pull it free from your device.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Autore

con 2 altri collaboratori

Joseph Lintz

Membro da: 09/15/16

915 Reputazione

5 Guide realizzate

Distintivi: 10

+7 altri distintivi

Team

USF Tampa, Team 11-5, Blackwell Fall 2016 Membro di USF Tampa, Team 11-5, Blackwell Fall 2016

USFT-BLACKWELL-F16S11G5

3 Membri

5 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 4

Tutti i Tempi: 605