Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn over laptop so that the bottom is showing.
-
Unlock the latch.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the back cover and you will then be able to see the battery.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Unlatch the two latches securing the battery in the case.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use a plastic opening tool to lift and remove the battery.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the hard drive by unscrewing the four 8mm screws with the T7 philip's head.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Pry off ten rubber paddings on the outer edge of the laptop to reveal the torx screws.
-
Unscrew the ten 8mm torx screws that are under the rubber paddings using the T7 tip torx screwdriver.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 4mm screws indicated by the M2.5X4 using the J00 tip screwdriver.
-
Remove SD card cap by just sliding out to reveal one screw.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 3mm screws indicated by the M2.03 using the J00 tip screwdriver.
-
Remove the 4mm SD card screw using the J00 tip.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the one 4mm fan screw using the J00 tip screwdriver.
-
Remove screw and metal plate to expose ribbon cable connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use an opening tool to pry up the ribbon connector to disconnect.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn laptop over back to normal position as shown in the image.
-
Use opening tools to pry up keyboard.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully lift keyboard on one side to expose the two ribbon cables.
-
Use an opening tool to lift up the locking clip and unplug the two ribbon cables.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Remove the two 4mm screws centered notated by the keyboard logo using the J00 tip.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Once keyboard has been fully removed, the system case containing the motherboard can be lifted out easily.
-
The display is connected to the shell of the laptop.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Unplug fan cable by pulling away from its connector.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Unscrew the two 6mm fan screws using the J00 tip.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Retrieve the monitor display connected to the plastic chassis.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Unscrew the two 4mm hinge screws using the Philips 00 tip screwdriver.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Unhinge the monitor display from the chassis.
-