Salta al contenuto principale

Introduzione

This guide walks through replacing a faulty camera. It requires removing the keyboard mount and lid. Afterwards, this guide requires a plastic opening tool and recommends tweezers to finish removal.

  1. Flip the laptop upside down so that the lid lies flat on the table. Remove the nine 6mm Phillips #00 screws that line the border.
    • Flip the laptop upside down so that the lid lies flat on the table.

    • Remove the nine 6mm Phillips #00 screws that line the border.

  2. Remove the two rubber feet closest to the hinge using tweezers. Remove the two 6mm Phillips #00 screws revealed under these rubber feet.
    • Remove the two rubber feet closest to the hinge using tweezers.

    • Remove the two 6mm Phillips #00 screws revealed under these rubber feet.

    • The rubber feet may tear while removal; preventing this can be difficult, but it won’t harm the laptop. If desired, replace these rubber feet during reassembly.

  3. Flip the laptop so it is in the upright position.
    • Flip the laptop so it is in the upright position.

    • Open the lid.

    • Unsnap the keyboard mount along the border of the laptop using a plastic opening tool.

    • This may require more force than expected. Hearing loud clicks as the plastic opening tool slides along the seam is normal.

  4. Tilt the keyboard mount up. Use a spudger to flip up the two ZIF connector retaining flaps for the ribbon cables that connect the keyboard mount to the motherboard. Gently remove both ribbon cables.
    • Tilt the keyboard mount up.

    • Use a spudger to flip up the two ZIF connector retaining flaps for the ribbon cables that connect the keyboard mount to the motherboard.

    • Gently remove both ribbon cables.

  5. Lift the keyboard mount out of the laptop.
    • Lift the keyboard mount out of the laptop.

  6. Gently tug on the black and white wires connected to the Wi-Fi module to disconnect them.
    • Gently tug on the black and white wires connected to the Wi-Fi module to disconnect them.

  7. Using a spudger, lift the ZIF retaining flap that secures the display’s ribbon cable to the motherboard. Gently pull the ribbon cable out of its socket.
    • Using a spudger, lift the ZIF retaining flap that secures the display’s ribbon cable to the motherboard.

    • Gently pull the ribbon cable out of its socket.

  8. Free the wire from the casing.
    • Free the wire from the casing.

  9. Remove the two 6mm Phillips #00 screws located near the upper left and right corners of the hinge mounts.
    • Remove the two 6mm Phillips #00 screws located near the upper left and right corners of the hinge mounts.

    • Hold the lid so that it is folded slightly inwards while removing the screws so that the lid doesn’t fall.

  10. Rotate the lid to a 90-degree angle with the table.
    • Rotate the lid to a 90-degree angle with the table.

    • Shimmy the lid out of the laptop.

  11. Use the plastic opening tool to pry the left and right side of the top of the lid, and proceed inwards from the sides. Do not attempt to remove the entire frame; this isn't necessary for removing the camera. Do not pry at the center of the lid; this may damage the camera inside.
    • Use the plastic opening tool to pry the left and right side of the top of the lid, and proceed inwards from the sides.

    • Do not attempt to remove the entire frame; this isn't necessary for removing the camera.

    • Do not pry at the center of the lid; this may damage the camera inside.

  12. Gently remove the slide-out connector near the bottom left corner of the camera mount.
    • Gently remove the slide-out connector near the bottom left corner of the camera mount.

  13. Locate the two silver strips of tape on each edge of the camera mount.
    • Locate the two silver strips of tape on each edge of the camera mount.

    • Use tweezers to peel off these strips.

  14. Use a plastic opening tool to pry the camera mount out of the lid.
    • Use a plastic opening tool to pry the camera mount out of the lid.

    • Apply force evenly to prevent bending the mount.

  15. Lift the camera out of the lid.
    • Lift the camera out of the lid.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

Rahul Goyal

Membro da: 26/04/2017

1.337 Reputazione

10 Guide realizzate

Team

Cal Poly, Team S23-G3, Livingston Spring 2017 Membro di Cal Poly, Team S23-G3, Livingston Spring 2017

CPSU-LIVINGSTON-S17S23G3

4 Membri

12 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 8

Tutti i Tempi: 285