Introduzione

This guide explains how to remove the Motherboard from the HP 15-f009wm notebook computer. This could be done to either replace a malfunctioning Motherboard or to upgrade to a stronger Motherboard.

  1. Turn laptop upside down.
    • Turn laptop upside down.

    • Flip the lock switch to the unlocked setting.

    Aggiungi Commento

  2. Flip the release switch.
    • Flip the release switch.

    • Once the flip is switched, the battery should pop out.

    Aggiungi Commento

    • Slide the battery out.

    Aggiungi Commento

    • Remove the two Phillips #1 screws from the RAM panel.

    Aggiungi Commento

    • Use the plastic opening tool to pop the panel off.

    Aggiungi Commento

    • Release the tabs on each side of the chip by simultaneously pushing each tab away from the RAM.

    • These tabs lock the chip in place and releasing them will cause the chip to "pop" up.

    Aggiungi Commento

    • Remove the RAM chip from the laptop.

    Aggiungi Commento

    • Remove the sixteen 7mm Phillips #1 screws from the bottom panel.

    Aggiungi Commento

    • Pull the disk drive out of the laptop.

    Aggiungi Commento

    • Remove the three 2mm Phillips #00 screws found underneath the disk drive.

    Aggiungi Commento

    • Remove the single 4mm Phillips #1 screw from the Wi-Fi card.

    • Pull the Wi-Fi card out of the motherboard.

    Aggiungi Commento

    • Open the laptop.

    • Use a plastic opening tool to pop out the keyboard by starting at the top and working your way around the perimeter.

    Aggiungi Commento

    • Open the screen up until it lays flat and rotate the laptop until the screen is closest to you.

    • Lift the keyboard from the laptop.

    • Use a spudger to lift up the black latch on the ZIF connector and remove the ribbon cable.

    Aggiungi Commento

    • Remove the five 7mm Phillips #1 screws found underneath the keyboard.

    Aggiungi Commento

    • Use a spudger to lift the black tabs on the ZIF connectors.

    • Remove the ribbon cables from the ZIF connectors.

    Aggiungi Commento

    • Use a plastic opening tool to pop the palm rest off of the laptop.

    • Lift and remove the palm rest.

    Aggiungi Commento

    • Use a spudger to lift up the black latch on the ZIF connector.

    • Remove the USB/AUX port ribbon cable from the ZIF connector on the motherboard.

    Aggiungi Commento

    • Remove the single 7mm Phillips #1 screw from the USB/AUX board.

    • Remove the USB/AUX board from the laptop.

    Aggiungi Commento

    • Lift the Hard Drive from the laptop.

    • Disconnect the hard drive from the motherboard.

    Aggiungi Commento

    • Remove the four 4mm Phillips #1 screws from the motherboard.

    • Lift the motherboard up from the computer.

      • There will be three wires connected underneath.

    Aggiungi Commento

    • Disconnect the speaker.

    Aggiungi Commento

    • Remove the display connection wire. Lift the connection straight up from the motherboard.

    Aggiungi Commento

    • Flip the motherboard over.

    • Disconnect the charging port wire from the motherboard.

    Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Alex Birchler

Membro da: 14/02/2018

733 Reputazione

5 Guide realizzate

Team

USF Tampa, Team S2-G2, Nance Spring 2018 Membro di USF Tampa, Team S2-G2, Nance Spring 2018

USFT-NANCE-S18S2G2

4 Membri

5 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 13

Ultimi 30 Giorni: 19

Tutti i Tempi: 119