/
Il mio banco da lavoro

Ottieni un rapido accesso alle guide, ai componenti e alle risposte per i tuoi dispositivi

DE
Deutsch
ES
Español
IT
Italiano
PT
Português
TR
Türkçe
JP
日本語
EN
English
FR
Français
NL
Nederlands
RU
Pусский
ZH
中文
KO
한국어
Unisciti
Accedi
Unisciti alla più grande community di riparazione al mondo
Ricambi
GuideRisposte
Modifica
Graco Secure Coverage LED Nursery Unit Replacement

Graco Secure Coverage LED Nursery Unit Replacement

Bryson Wolff

Bryson Wolff e 2 altri collaboratori

Ultimo aggiornamento il December 7, 2015

Nessuna stima
Moderato
Inconveniente Markup

Introduzione

Vai al passo 1

Use this guide to replace the LED on your Graco Secure Coverage Digital Baby Monitor for nursery unit.

The LED replacement includes the LED and battery replacement.

Cosa ti serve

Strumenti

Mostra di più…

  1. Graco Secure Coverage LED Nursery Unit Replacement, Nursery Unit Battery: passo 1, immagine 1 di 3 Graco Secure Coverage LED Nursery Unit Replacement, Nursery Unit Battery: passo 1, immagine 2 di 3 Graco Secure Coverage LED Nursery Unit Replacement, Nursery Unit Battery: passo 1, immagine 3 di 3

    • Remove the 9mm screw from the battery cover of the nursery unit using a Phillips #1 tip screwdriver.

    Modifica

  2. Graco Secure Coverage LED Nursery Unit Replacement: passo 2, immagine 1 di 2 Graco Secure Coverage LED Nursery Unit Replacement: passo 2, immagine 2 di 2

    • Using the plastic opening tool, pry and remove the battery cover carefully.

    • Remove the batteries using plastic opening tool.

    • Replace the batteries.

    Modifica

  4. Graco Secure Coverage LED Nursery Unit Replacement, LED Nursery Unit: passo 3, immagine 1 di 2 Graco Secure Coverage LED Nursery Unit Replacement, LED Nursery Unit: passo 3, immagine 2 di 2

    • Remove the two 9mm Phillips #1 screws from the rare case of the device.

    • Place the screws in a secure place.

    Modifica

  5. Graco Secure Coverage LED Nursery Unit Replacement: passo 4, immagine 1 di 1

    • Hold the bottom of the device with one hand and pull down to separate the front and rare cases.

    • While holding the device with one hand, use plastic opening tool to pry the edges of the front case away from the back case.

    • Apply constant force carefully to avoid breaking any other plastic parts from the device.

    Modifica

  6. Graco Secure Coverage LED Nursery Unit Replacement: passo 5, immagine 1 di 2 Graco Secure Coverage LED Nursery Unit Replacement: passo 5, immagine 2 di 2

    • Remove all three 7mm Phillips #1 screws from the mother board.

    • Place the screws in secure place.

    Modifica

  7. Graco Secure Coverage LED Nursery Unit Replacement: passo 6, immagine 1 di 3 Graco Secure Coverage LED Nursery Unit Replacement: passo 6, immagine 2 di 3 Graco Secure Coverage LED Nursery Unit Replacement: passo 6, immagine 3 di 3

    • Flip over the motherboard to look at the LED pins that are connected to it.

    • Solder off the LED pin from the motherboard.

    • There are many pins are connect to the motherboard, so make sure that you solder off the LED pin.

    • Replace the LED.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 2 altri collaboratori

Bryson Wolff

Membro da: 08/31/15

237 Reputazione

2 Guide realizzate

Distintivi: 10

+7 altri distintivi

Team

USF Tampa, Team 6-5, Remmell Fall 2015 Membro di USF Tampa, Team 6-5, Remmell Fall 2015

USFT-REMMELL-F15S6G5

4 Membri

8 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 3

Tutti i Tempi: 173