Salta al contenuto principale

GoPro Karma Arms Replacement

Cosa ti serve

  1. GoPro Karma Arms Replacement, Battery: passo 1, immagine 1 di 1
    • Hook your fingers on the tab and pull out the battery.

  2. GoPro Karma Arms Replacement, Stabilizer: passo 2, immagine 1 di 3 GoPro Karma Arms Replacement, Stabilizer: passo 2, immagine 2 di 3 GoPro Karma Arms Replacement, Stabilizer: passo 2, immagine 3 di 3
    • Locate stabilizer collar’s unlock and lock symbols. Twist the collar counterclockwise to unlock the stabilizer from GoPro Karma body.

    • Place the GoPro Karma on a stable surface with the legs folded in and the stabilizer facing towards yourself.

  3. GoPro Karma Arms Replacement: passo 3, immagine 1 di 1
    • Remove the stabilizer by pulling the entire stabilizer out of the drone body.

  4. GoPro Karma Arms Replacement, Landing Gear: passo 4, immagine 1 di 1
    • Flip the drone upside down with the landing gear out.

    • Remove the four 1.2 cm long hex screws with a Hex 2.0 screwdriver in the four corners of the landing gear

  5. GoPro Karma Arms Replacement: passo 5, immagine 1 di 1
    • Push with your thumb and pull up with your fingers to remove the landing gear.

    • Caution: The landing gear is connected by a thin cable so do not pull too far away.

  6. GoPro Karma Arms Replacement: passo 6, immagine 1 di 2 GoPro Karma Arms Replacement: passo 6, immagine 2 di 2
    • Flip over the landing gear and locate the cable connector.

    • Use your thumbnail to disconnect the cable and free the landing gear.

  7. GoPro Karma Arms Replacement, Arms: passo 7, immagine 1 di 1
    • Remove the two 1.2 cm long hex screws with a Hex 2.0 screwdriver and set them aside.

  8. GoPro Karma Arms Replacement: passo 8, immagine 1 di 2 GoPro Karma Arms Replacement: passo 8, immagine 2 di 2
    • Remove both locked connectors by pushing the connector release tool into the hole in the center and pulling up with the white handles.

    • The connector release tool is only included with the purchase of a replacement arm from the GoPro website.

    • If you do not have a connector release tool, use a small screwdriver to push each tab while pulling up with the white handles.

  9. GoPro Karma Arms Replacement: passo 9, immagine 1 di 3 GoPro Karma Arms Replacement: passo 9, immagine 2 di 3 GoPro Karma Arms Replacement: passo 9, immagine 3 di 3
    • Remove the cover plate by pulling up on the side.

    • Feed each connector through the hole and set aside the cover plate.

  10. GoPro Karma Arms Replacement: passo 10, immagine 1 di 2 GoPro Karma Arms Replacement: passo 10, immagine 2 di 2
    • Loosen the 2 cm long hex screw in the arm with a Hex 2.0 screwdriver.

    • The screw will not come out but loosen it until it can rotate easily.

    • Pull up and off the broken arm.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Kyle Hoff

Membro da: 04/23/18

141 Reputazione

1 Guida realizzata

Team

Cal Poly, Team S25-G14, Maness Spring 2018 Membro di Cal Poly, Team S25-G14, Maness Spring 2018

CPSU-MANESS-S18S25G14

4 Membri

6 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 12

Ultimi 30 Giorni: 28

Tutti i Tempi: 2,119