Aggiusta la tua roba Comunità Store

GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement

Cosa ti serve

  1. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement, Casing: passo 1, immagine 1 di 1

    • Power off your GoPro before beginning disassembly.

    • Unclip the black latch to the camera case and open the case.

    Modifica

  2. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: passo 2, immagine 1 di 1

    • Gently pry the back open by inserting a metal spudger between the case and back panel.

    Modifica

  3. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: passo 3, immagine 1 di 1

    • Disconnect the battery from the motherboard by unplugging the red, white, and black wires from the white adapter.

    Modifica

  5. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: passo 4, immagine 1 di 1

    • Disconnect the ribbon cable from the lens by lifting the black latch and gently pulling the ribbon cable from the socket.

    Modifica

  6. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: passo 5, immagine 1 di 1

    • Use a Phillips screwdriver (PH000) to remove the four screws around the white plastic piece.

    • Make sure to keep track of these screws as they are very small.

    Modifica

  7. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: passo 6, immagine 1 di 1

    • Carefully remove the motherboard and white plastic piece from the case.

    Modifica

  8. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement, Micro USB/MicroSD Card Daughter Board: passo 7, immagine 1 di 2 GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement, Micro USB/MicroSD Card Daughter Board: passo 7, immagine 2 di 2

    • Remove the larger ribbon cable from the daughter board by lifting the black latch and pulling the ribbon cable gently from the socket.

    • Disconnect the smaller ribbon cable leading from the white plastic piece by simply pulling it from the socket.

    Modifica

  9. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: passo 8, immagine 1 di 1

    • Remove the two screws located on each side of the board with a Phillips screwdriver.

    • The screws go through an L metal bracket that will come off with the screws.

    Modifica

  10. GoPro Hero Micro USB/MicroSD Card Daughter BoardReplacement: passo 9, immagine 1 di 1

    • Separate the daughter board from the white plastic piece.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 5 persone hanno completato questa guida.

Autore

con 3 altri collaboratori

River Drake

Membro da: 04/02/15

1.035 Reputazione

5 Guide realizzate

Distintivi: 15

+12 altri distintivi

Team

Cal Poly, Team 12-2, Lancaster Spring 2015 Membro di Cal Poly, Team 12-2, Lancaster Spring 2015

CPSU-LANCASTER-S15S12G2

4 Membri

18 Guide realizzate

4 Commenti

Wo kann ich ein daughterboard kaufen habt ihr da was für mich?

Lukas Blohm - Replica

bravo! è scritto molto bene ed è stato utile. ma dove trovo il ricambio? non ci riesco!!!

michele - Replica

Terrific guide. Does anyone know where to buy the “daughter board”?

fedebossert - Replica

ide. Does anyone know where to buy the “daughter board”?

fedebossert - 05/27/20

<a href="https://www.w3schools.com/">Visit W3Schools.com!</a>

pavan kalyan - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 14

Tutti i Tempi: 4,767