Salta al contenuto principale

GoPro Hero 3 Silver Expansion Port Replacement

Cosa ti serve

  1. GoPro Hero 3 Silver Expansion Port Replacement, Battery: passo 1, immagine 1 di 2 GoPro Hero 3 Silver Expansion Port Replacement, Battery: passo 1, immagine 2 di 2
    • Pull back on the tab on the back of GoPro to open the battery cover.

  2. GoPro Hero 3 Silver Expansion Port Replacement: passo 2, immagine 1 di 1
    • Pull the battery out using the tab.

  3. GoPro Hero 3 Silver Expansion Port Replacement, Expansion Port: passo 3, immagine 1 di 2 GoPro Hero 3 Silver Expansion Port Replacement, Expansion Port: passo 3, immagine 2 di 2
    • Use the plastic opening tool to remove the faceplate.

    • There is some adhesive and clips so be careful and the faceplate should pop right off.

  4. GoPro Hero 3 Silver Expansion Port Replacement: passo 4, immagine 1 di 2 GoPro Hero 3 Silver Expansion Port Replacement: passo 4, immagine 2 di 2
    • Now that the faceplate is off, it is time to remove the 4 screws on each corner.

    • Use the T4 tool bit from the iFixit toolkit in order to remove the 4 screws on each corner.

  5. GoPro Hero 3 Silver Expansion Port Replacement: passo 5, immagine 1 di 2 GoPro Hero 3 Silver Expansion Port Replacement: passo 5, immagine 2 di 2
    • Note: Make sure you remove the door cover of the USB, mini HDMI, and SD port before. Separating the motherboard will be easier.

    • Using the plastic opening tool, slowly pry open the motherboard assembly.

  6. GoPro Hero 3 Silver Expansion Port Replacement: passo 6, immagine 1 di 2 GoPro Hero 3 Silver Expansion Port Replacement: passo 6, immagine 2 di 2
    • Use the spudger to gently pry off the connector of the housing to the motherboard.

    • You should now have the motherboard assembly and the housing separated.

  7. GoPro Hero 3 Silver Expansion Port Replacement: passo 7, immagine 1 di 3 GoPro Hero 3 Silver Expansion Port Replacement: passo 7, immagine 2 di 3 GoPro Hero 3 Silver Expansion Port Replacement: passo 7, immagine 3 di 3
    • Use the spudger to remove the heat shield tape and detach the image sensor from the motherboard.

    • Using the T4 Torx toolbit, remove the 4 screws that connect the sensor to the lens.

    • Remove the silver connector of the image sensor from the motherboard using the spudger to pry it off.

  8. GoPro Hero 3 Silver Expansion Port Replacement: passo 8, immagine 1 di 2 GoPro Hero 3 Silver Expansion Port Replacement: passo 8, immagine 2 di 2
    • The media adapter is attached to the motherboard via 3 screws:

    • x1 T4 Torx

    • x2 Phillips #00

    • There is a little silver bracket (in the yellow circle) that is held down by the Phillips #00 screw so be careful not to lose it.

  9. GoPro Hero 3 Silver Expansion Port Replacement: passo 9, immagine 1 di 2 GoPro Hero 3 Silver Expansion Port Replacement: passo 9, immagine 2 di 2
    • With a little prying, use the spudger to detach the media adapter's connector from the motherboard.

    • Remove the media adapter from the motherboard.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Brian Alvarez

Membro da: 04/02/15

1.439 Reputazione

6 Guide realizzate

Team

Cal Poly, Team 24-7, Lancaster Spring 2015 Membro di Cal Poly, Team 24-7, Lancaster Spring 2015

CPSU-LANCASTER-S15S24G7

3 Membri

21 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 5

Tutti i Tempi: 1,837