Salta al contenuto principale

GoPro Hero 3+ Silver Edition Motherboard Replacement

Cosa ti serve

  1. GoPro Hero 3+ Silver Edition Motherboard Replacement, Battery: passo 1, immagine 1 di 2 GoPro Hero 3+ Silver Edition Motherboard Replacement, Battery: passo 1, immagine 2 di 2
    • Push the tab on the back of the device left to remove the plate covering the battery.

  2. GoPro Hero 3+ Silver Edition Motherboard Replacement: passo 2, immagine 1 di 1
    • Use the strip of tape on the battery to remove the battery from the housing.

  3. GoPro Hero 3+ Silver Edition Motherboard Replacement, Front Panel: passo 3, immagine 1 di 1
    • Insert a plastic opening tool in between the front face plate and the black housing.

    • Make sure you insert the plastic opening tool next to the microSD card slot. There is a small gap that will help separate the face plate.

  4. GoPro Hero 3+ Silver Edition Motherboard Replacement: passo 4, immagine 1 di 1
    • Continue to use the plastic opening tool and separate the front face plate from the rest of the device.

    • There is adhesive that helps attach the front face plate. Some extra prying may be required to separate the face plate, but do not use excessive force.

  5. GoPro Hero 3+ Silver Edition Motherboard Replacement, Image Sensor: passo 5, immagine 1 di 3 GoPro Hero 3+ Silver Edition Motherboard Replacement, Image Sensor: passo 5, immagine 2 di 3 GoPro Hero 3+ Silver Edition Motherboard Replacement, Image Sensor: passo 5, immagine 3 di 3
    • Locate the four 8.1mm PH00 screws on the corners of the GoPro and unscrew them using the phillips screwdriver.

    • Gently remove the motherboard by using a plastic opening tool to pry it out of the housing.

    • Be careful not to damage the ribbon cable connected to the GoPro housing and motherboard.

    Is this the power cable?

    David - Replica

  6. GoPro Hero 3+ Silver Edition Motherboard Replacement: passo 6, immagine 1 di 2 GoPro Hero 3+ Silver Edition Motherboard Replacement: passo 6, immagine 2 di 2
    • Remove the ribbon cable by carefully flipping the black clip up with the plastic opening tool and pulling the cable out.

  7. GoPro Hero 3+ Silver Edition Motherboard Replacement: passo 7, immagine 1 di 1
    • Remove the four 4mm PH00 screws attaching the image sensor to the motherboard with your screwdriver.

  8. GoPro Hero 3+ Silver Edition Motherboard Replacement: passo 8, immagine 1 di 2 GoPro Hero 3+ Silver Edition Motherboard Replacement: passo 8, immagine 2 di 2
    • Pry off the last ribbon cable with a plastic opening tool.

    • Remove the image sensor from the motherboard.

  9. GoPro Hero 3+ Silver Edition Motherboard Replacement, Motherboard: passo 9, immagine 1 di 1
    • Remove the single 3.2mm PH00 screw with your screwdriver to detach the motherboard from the mid frame.

  10. GoPro Hero 3+ Silver Edition Motherboard Replacement: passo 10, immagine 1 di 3 GoPro Hero 3+ Silver Edition Motherboard Replacement: passo 10, immagine 2 di 3 GoPro Hero 3+ Silver Edition Motherboard Replacement: passo 10, immagine 3 di 3
    • Use a plastic opening tool to gently separate the LCD ribbon cable from the motherboard.

    • Gently remove the motherboard from the midframe using tweezers.

    • Remove motherboard by lifting from the edges. This will reduce the chance of damaging components on the motherboard.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

Team

Cal Poly, Team 5-8, Maness Fall 2015 Membro di Cal Poly, Team 5-8, Maness Fall 2015

CPSU-MANESS-F15S5G8

4 Membri

12 Guide realizzate

2 Commenti

hi, where i can find the matherboard for de hero 3+ silver?

Mauricio - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 8

Tutti i Tempi: 3,436