Aggiusta la tua roba Comunità Store

Giant Reign 2 Tube Replacement

Introduzione

Installing a tube.

Cosa ti serve

  1. Giant Reign 2 Tube Replacement, Hex Screws: passo 1, immagine 1 di 1

    • Using the 4mm Allen wrench, partially unscrew the 4 (22mm) hex screws on the front of the axle casing to allow the axle to slide freely.

    Modifica

  2. Giant Reign 2 Tube Replacement, Axle Screw: passo 2, immagine 1 di 2 Giant Reign 2 Tube Replacement, Axle Screw: passo 2, immagine 2 di 2

    • Using the 8mm Allen wrench, loosen the axle screw until 1/2 of the axle screw is visible.

    • Push the axle screw to reveal the axle rod on the other side.

    Modifica

  3. Giant Reign 2 Tube Replacement: passo 3, immagine 1 di 1

    • Using the Allen wrench, finish unscrewing the axle screw and pull it out.

    • Hold the wheel when pulling out the axle rod so that the bike does not fall.

    Modifica

  4. Giant Reign 2 Tube Replacement, Front Wheel: passo 4, immagine 1 di 1

    • Pull the wheel from the fork.

    Modifica

  5. Giant Reign 2 Tube Replacement, Tube: passo 5, immagine 1 di 1

    • Look at your tire and determine the correct tube size by locating the number (formated ## x #.##) on the wall of the tire.

    • Bike tubes come with one of two standard valve types: presta and schrader. These guides show the installation of a tube with a presta valve.

    Modifica

  7. Giant Reign 2 Tube Replacement: passo 6, immagine 1 di 3 Giant Reign 2 Tube Replacement: passo 6, immagine 2 di 3 Giant Reign 2 Tube Replacement: passo 6, immagine 3 di 3

    • Unscrew the cap covering the valve.

    • Remove the spacer that holds the valve in place against the rim of the wheel.

    • Open the valve by turning the nut and pressing the valve in to release air pressure from the tube.

    Modifica

  8. Giant Reign 2 Tube Replacement: passo 7, immagine 1 di 3 Giant Reign 2 Tube Replacement: passo 7, immagine 2 di 3 Giant Reign 2 Tube Replacement: passo 7, immagine 3 di 3

    • Slide the tire lever between the tire and the rim.

    • Push down on the tire lever until the edge of the tire is higher than the edge of the rim.

    • Insert a second tire lever adjacent to the first.

    • Slowly work one tire lever around the rim until the whole tire is loose.

    Modifica

  9. Giant Reign 2 Tube Replacement: passo 8, immagine 1 di 2 Giant Reign 2 Tube Replacement: passo 8, immagine 2 di 2

    • Press the valve through the rim of the wheel.

    • Remove the tube from the tire.

    Modifica

  10. Giant Reign 2 Tube Replacement: passo 9, immagine 1 di 1

    • Partially inflate the tube.

    Modifica

  11. Giant Reign 2 Tube Replacement: passo 10, immagine 1 di 2 Giant Reign 2 Tube Replacement: passo 10, immagine 2 di 2

    • Push the valve through the rim.

    • Push the tube into the tire all the way around the rim of the wheel.

    Modifica

  12. Giant Reign 2 Tube Replacement: passo 11, immagine 1 di 1

    • Push the bead of the tire back into place around the rim.

    • Make sure not to pinch the tube between the bead of the tire and the rim. Failure to do so may cause a pinch flat.

    Modifica

  13. Giant Reign 2 Tube Replacement: passo 12, immagine 1 di 1

    • Inflate the tube to the desired air pressure.

    • A suggested range of air pressure is located on the wall of the tire (formatted ##-##psi).

    Modifica

  14. Giant Reign 2 Tube Replacement: passo 13, immagine 1 di 2 Giant Reign 2 Tube Replacement: passo 13, immagine 2 di 2

    • Close the valve and replace the cap.

    Modifica
Linea Traguardo

Un'altra persona ha completato questa guida.

Autore

con 5 altri collaboratori

Sterling Grande

Membro da: 10/08/12

148 Reputazione

4 Guide realizzate

Distintivi: 7

+4 altri distintivi

Team

Cal Poly, Team 9-14, Amido Fall 2012 Membro di Cal Poly, Team 9-14, Amido Fall 2012

CPSU-AMIDO-F12S9G14

4 Membri

10 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 10

Tutti i Tempi: 2,846