Aggiusta la tua roba Comunità Store

General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement

Introduzione

Use this guide to replace the reverse switch on a General Pipe Cleaners Drain Cleaner EJB 2014.

Cosa ti serve

  1. General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement, Reverse Switch: passo 1, immagine 1 di 1

    • Before you begin, make sure the drain cleaner is disconnected from power.

    • Use a Phillips #2 driver to remove the two screws securing the control box cover.

    Modifica

  2. General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 2, immagine 1 di 1

    • Remove the control box cover.

    Modifica

  3. General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 3, immagine 1 di 1

    • Use a 9/16 inch deep socket and ratchet to remove the nut securing the reverse switch.

    Modifica

  5. General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 4, immagine 1 di 2 General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 4, immagine 2 di 2

    • Remove the reverse switch guard.

    Modifica

  6. General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 5, immagine 1 di 2 General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 5, immagine 2 di 2

    • Squeeze the tabs on either side of the reverse switch connector.

    • Pull the two halves of the connector apart to disconnect it.

    • Take note of where everything is connected in the control box before disconnecting anything else.

    Modifica

  7. General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 6, immagine 1 di 2 General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 6, immagine 2 di 2

    • Pull the white cable straight off of its spade connector on the power switch diaphragm.

    Modifica

  8. General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 7, immagine 1 di 2 General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 7, immagine 2 di 2

    • Pull the black cable straight off of its spade connector on the power switch diaphragm.

    Modifica

  9. General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 8, immagine 1 di 3 General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 8, immagine 2 di 3 General Pipe Cleaners Drain Cleaner EJB 2014 Reverse Switch Replacement: passo 8, immagine 3 di 3

    • Slide the switch assembly down out of its hole in the control box and pull it out of the control box.

    • Be careful not to snag the switch on any cables during removal.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Autore

Adam O'Camb

Membro da: 04/11/15

196.940 Reputazione

416 Guide realizzate

Distintivi: 39

+36 altri distintivi

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 8

Ultimi 30 Giorni: 28

Tutti i Tempi: 978