Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Garmin Nuvi 680 Motherboard Replacement

Introduzione

A step-by-step guide to replacing the motherboard in the Garmin Nuvi 680.

Cosa ti serve

  1. Garmin Nuvi 680 Motherboard Replacement, Outer Case: passo 1, immagine 1 di 1

    • Flip open the antenna on the back of the device.

    • Remove the two 4.42 mm screws on the antenna cover using a T5 Torx screwdriver.

    Traduci

  2. Garmin Nuvi 680 Motherboard Replacement: passo 2, immagine 1 di 1

    • Remove the antenna cover.

    Traduci

  3. Garmin Nuvi 680 Motherboard Replacement: passo 3, immagine 1 di 1

    • The yellow wire is connected to the motherboard, so you cannot disconnect it until you finish opening the device.

    • Pull the antenna circuit board out of its case.

    Traduci

  4. Garmin Nuvi 680 Motherboard Replacement: passo 4, immagine 1 di 2 Garmin Nuvi 680 Motherboard Replacement: passo 4, immagine 2 di 2

    • Insert the pointed end of a spudger into the leftmost slit of the antenna case.

    • Push the spudger to the right.

    • Slide the antenna case out slowly or you may lose the antenna's spring. The spring is inside the black plastic that holds the antenna case to the device.

    • Slide the antenna case out of the device.

    • Reinstallation tip: first reassemble the antenna casing (place antenna back into its plastic cover), and then re-insert the entire assembly back into the GPS body.

    Traduci

  5. Garmin Nuvi 680 Motherboard Replacement: passo 5, immagine 1 di 1

    • Remove the two screws on the back of the outer case using a T5 Torx screwdriver.

    • These screws are 10.82 mm long.

    Traduci

  7. Garmin Nuvi 680 Motherboard Replacement: passo 6, immagine 1 di 2 Garmin Nuvi 680 Motherboard Replacement: passo 6, immagine 2 di 2

    • Gently pull apart the front and back of the device. The front and back are still connected by ribbon cables.

    • Starting along the top, separate the front and back of the device by pushing an iPod-opening tool into the crack along each side of the case.

    Traduci

  8. Garmin Nuvi 680 Motherboard Replacement, Antenna: passo 7, immagine 1 di 2 Garmin Nuvi 680 Motherboard Replacement, Antenna: passo 7, immagine 2 di 2

    • Use a spudger to disconnect the yellow antenna wire from the ZIF connector by opening the brown latch holding the wire in place.

    • Remove the antenna.

    Traduci

  9. Garmin Nuvi 680 Motherboard Replacement, Screen Wiring: passo 8, immagine 1 di 1

    • Do not remove the ribbon cables without lifting the latch or the cable will be damaged.

    • Lift the latches on the ribbon cable connectors. All the ribbon cables may have latches. The right most latch may have a latch that flips in the opposite direction from the others.

    • Gently pull the ribbon cables out of their connectors. They should slide out easily.

    • Do not separate the two halves of the device yet or the on/off cable may be severed.

    Traduci

  10. Garmin Nuvi 680 Motherboard Replacement: passo 9, immagine 1 di 2 Garmin Nuvi 680 Motherboard Replacement: passo 9, immagine 2 di 2

    • Gently pull the cable for the on/off button straight up to remove it.

    • The two halves of the device may now be separated.

    Traduci

  11. Garmin Nuvi 680 Motherboard Replacement, Motherboard: passo 10, immagine 1 di 1

    • Use a PH1 sized Philips screwdriver to remove the two screws shown.

    • These screws are 6.88 mm long

    Traduci

  12. Garmin Nuvi 680 Motherboard Replacement: passo 11, immagine 1 di 2 Garmin Nuvi 680 Motherboard Replacement: passo 11, immagine 2 di 2

    • Carefully separate the motherboard from the outer case or the speaker and battery cables may be damaged.

    • Use a spudger to lift the edge of the motherboard.

    Traduci

  13. Garmin Nuvi 680 Motherboard Replacement: passo 12, immagine 1 di 1

    • Gently unplug the cable for the battery

    • Gently unplug the cable for the speaker.

    Traduci

  14. Garmin Nuvi 680 Motherboard Replacement: passo 13, immagine 1 di 1

    • Lift the motherboard out of the outer case.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Autore

con 8 altri collaboratori

Chris Marzano

Membro da: 01/20/11

968 Reputazione

6 Guide realizzate

Distintivi: 14

+11 altri distintivi

Team

Cal Poly, Team 5-22, Amido Winter 2011 Membro di Cal Poly, Team 5-22, Amido Winter 2011

CPSU-AMIDO-W11S5G22

5 Membri

7 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 3,615