/
DE
Deutsch
ES
Español
IT
Italiano
PT
Português
TR
Türkçe
JP
日本語
EN
English
FR
Français
NL
Nederlands
RU
Pусский
ZH
中文
KO
한국어
Unisciti
Accedi
Unisciti alla più grande community di riparazione al mondo
Ricambi
GuideRisposte
Traduci
GD Midea FT30-3D Power/Speed Switch Replacement

GD Midea FT30-3D Power/Speed Switch Replacement

Alan Su

Alan Su e 4 altri collaboratori

Ultimo aggiornamento il January 28, 2014

5 - 10 minuti
Moderato
Foto Azione
Introduzione Migliore

Cosa ti serve

Strumenti

Mostra di più…

  1. GD Midea FT30-3D Power/Speed Switch Replacement, Bottom Base: passo 1, immagine 1 di 1

    • Locate and remove the 14.5 mm Phillips #1 screw on the bottom of the fan base.

    Traduci

  2. GD Midea FT30-3D Power/Speed Switch Replacement: passo 2, immagine 1 di 2 GD Midea FT30-3D Power/Speed Switch Replacement: passo 2, immagine 2 di 2

    • Locate the gray base support release tabs found on either side pictured in the first image.

    • There are release tabs on each side of the base.

    • Press both release tabs in with the tip of your fingers and pull the gray base support until the tabs are cleared.

    Traduci

  3. GD Midea FT30-3D Power/Speed Switch Replacement: passo 3, immagine 1 di 1

    • Continue removing the gray base support by pressing your thumb into the circular opening in the base and pulling with your figures on the back side.

    • Notice that on the internal front tip of the base there is a tab. Because of this tab the back end will pivot off at that point.

    Traduci

  5. GD Midea FT30-3D Power/Speed Switch Replacement: passo 4, immagine 1 di 1

    • After the base has separated more it will be easy to fully remove it. Continue pulling the back edge of the gray base support, rotating it around the front tab until it comes off completely.

    Traduci

  6. GD Midea FT30-3D Power/Speed Switch Replacement: passo 5, immagine 1 di 1

    • Remove the following five 14.5 mm Phillips #1 screws found on the bottom.

    • All of the screws are recessed by 17.5 mm, so ensure your screwdriver can reach that far.

    Traduci

  7. GD Midea FT30-3D Power/Speed Switch Replacement: passo 6, immagine 1 di 1

    • Once all five screws have been removed the base cover should fall right off with out any effort.

    • When putting the base cover back on; be careful to make sure that none of the wires are pinched.

    Traduci

  8. GD Midea FT30-3D Power/Speed Switch Replacement, Power/Speed Switch: passo 7, immagine 1 di 1

    • Remove the two 10 mm Phillips #1 screws found connecting the switch to the case.

    • Notice the AC power cord line (white wire) goes into the switch under the [Off] button

    Traduci

  9. GD Midea FT30-3D Power/Speed Switch Replacement: passo 8, immagine 1 di 1

    • Take the 1.5 mm Flathead Screwdriver, or any thin elongated tool that fits into the semi-circular holes along side the wires. Press into the hole gently to release the grip on the wires.

    • The wires should release with ease if done properly.

    • When reassembling; skip this step.

    Traduci

  10. GD Midea FT30-3D Power/Speed Switch Replacement: passo 9, immagine 1 di 1

    • Take the new switch, and simply push the wiring into the correct holes:

    • AC Power Cord (white wire)

    • Low speed (gray wire)

    • Medium speed (orange wire)

    • High speed (red wire)

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Autore

con 4 altri collaboratori

Alan Su

Membro da: 10/03/12

810 Reputazione

6 Guide realizzate

Distintivi: 12

+9 altri distintivi

Team

Cal Poly, Team 24-28, Regan Fall 2012 Membro di Cal Poly, Team 24-28, Regan Fall 2012

CPSU-REGAN-F12S24G28

4 Membri

14 Guide realizzate

0Commenti sulla guida

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 11

Tutti i Tempi: 3,820