Questa versione può contenere modifiche errate. Passa all'ultima istantanea verificata.
Cosa ti serve
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the multimeter so it is display side down.
-
Lift up the back stand of the device by putting your thumb in the curved well at the bottom of the device, so you have access to the two covered screws below.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use your Phillips #2 Screwdriver to remove the four black 21 mm Phillips #2 screws.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the Fluke 77 Series III Multimeter back over so that it is display side up.
-
Pry the front panel from the back panel at the seam.
-
If the front panel does not come off easily, move a plastic opening tool along the seam until the panels separate completely.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Locate the 9V battery in the lower right corner of the device.
-
Pull the battery out of its terminal.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Detach the two metal snaps from the battery.
-
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Locate the fuses near the bottom left corner inside the device.
-
The .440 Amp fuse is located in the upper left hand fuse holder.
-
The 11 Amp fuse is located in the lower right hand fuse holder.
-
Lift the rounded edge of the fuse with one finger until that side is completely out of its holder.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Grab the lifted edge of the fuse between your thumb and forefinger and pull it the rest of the way out of the device.
-
Repeat steps 4 and 5 to remove the other fuse if you are replacing both fuses or if you are replacing a different part further on.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Locate the rubber range and hold buttons in the internal assembly. These are found just below the LCD screen on the left hand side.
-
Remove the rubber range and hold button part with your thumb and forefinger.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Locate the silver 7 mm screw found underneath the 11A fuse.
-
Using the Phillips #0 Screwdriver, unscrew and remove the silver 7 mm Phillips #0 screw that attaches the back panel to the internal cover.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Lift the grey internal cover out of the back panel.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the internal assembly over so that the green circuit board (PCA) is visible.
-
Locate the five silver 11 mm Phillips #1 screws on the upper part of the circuit board that hold it to the the grey plastic internal cover.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Use the Phillips #1 Screwdriver to remove the five silver 11 mm Phillips #1 screws attaching the green circuit board to the grey plastic internal cover.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Carefully lift the circuit board up and away from the internal cover.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Turn the internal cover over with both hands.
-
Pry off the LCD screen bracket bordering the display.
-
-
Questo passaggio è privo di traduzione. Aiuta a tradurlo
-
Cover the LCD display with one of your hands.
-
Turn the internal cover over so that the LCD display is face down.
-
Slowly pull up the internal cover. The LCD display should fall right into your hand.
-
Annulla: non ho completato questa guida.
Altre 8 persone hanno completato questa guida.
5 Commenti
Great job! Ive found that sometimes all it takes to get the LCD working again is to clean those pink rubber conductors and with isopropyl alcohol.
Good job .. can i make replacement display from fluk 179 to fluke 77 series 3 .. there are the same size with different model .. thank you
I just cracked the screen on my Fluke 79 III and this repair guide will be invaluable. If anyone can offer a part number for the screen or where I could buy one, I would be most appreciative.
FLUKE 1560856 for 175/177/179 Multimeters