Aggiusta la tua roba Comunità Store

Flip Video Ultra USB connector Replacement

Introduzione

This guide will walk you through how to remove and replace the USB connector should your device be broken or malfunctioning.

Cosa ti serve

  1. Flip Video Ultra USB connector Replacement, USB connector: passo 1, immagine 1 di 1

    • Unlock the battery cover by sliding the switch to the unlock position.

    Modifica

  2. Flip Video Ultra USB connector Replacement: passo 2, immagine 1 di 1

    • Remove the battery cover by sliding it down the camera.

    Modifica

  3. Flip Video Ultra USB connector Replacement: passo 3, immagine 1 di 1

    • Remove the batteries.

    Modifica

  4. Flip Video Ultra USB connector Replacement: passo 4, immagine 1 di 1

    • Slide the black upper casing off from the device.

    • This is a bit hard to get off, so don't be afraid to use a bit of force. There is no lock.

    Modifica

  6. Flip Video Ultra USB connector Replacement: passo 5, immagine 1 di 2 Flip Video Ultra USB connector Replacement: passo 5, immagine 2 di 2

    • Remove the six 1mm screws from front of the camera with the Phillips Head screwdriver.

    Modifica

  7. Flip Video Ultra USB connector Replacement: passo 6, immagine 1 di 1

    • Remove the top casing from the bottom to reveal the inner circuit board.

    Modifica

  8. Flip Video Ultra USB connector Replacement: passo 7, immagine 1 di 2 Flip Video Ultra USB connector Replacement: passo 7, immagine 2 di 2

    • When removing the back panel, the rubber buttons will become loose and likely fall off the board. This is normal and can easily placed back on the board once finished.

    • Remove the six 1mm screws with the 1 Phillips head screwdriver.

    Modifica

  9. Flip Video Ultra USB connector Replacement: passo 8, immagine 1 di 2 Flip Video Ultra USB connector Replacement: passo 8, immagine 2 di 2

    • Gently separate the circuit board from the casing.

    Modifica

  10. Flip Video Ultra USB connector Replacement: passo 9, immagine 1 di 2 Flip Video Ultra USB connector Replacement: passo 9, immagine 2 di 2

    • Remove the three 1mm screws from the USB connector and back casing with the Phillips Head screwdriver.

    Modifica

  11. Flip Video Ultra USB connector Replacement: passo 10, immagine 1 di 2 Flip Video Ultra USB connector Replacement: passo 10, immagine 2 di 2
    Attrezzo utilizzato in questo passaggio:
    Tweezers
    $4.99
    Compra

    • Gently lift the usb connector using the Plastic opening tool.

    • Using tweezers, remove the cord from the motherboard by gently lifting the connector.

    • The connector will be easier to remove if you wiggle the tweezers while lifting.

    Modifica

  12. Flip Video Ultra USB connector Replacement: passo 11, immagine 1 di 1

    • Fully remove the USB connector and replace it with the new USB connector.

    Modifica
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Autore

con 4 altri collaboratori

Nathaniel Ruf

Membro da: 10/18/16

514 Reputazione

5 Guide realizzate

Distintivi: 5

+2 altri distintivi

Team

UMass Dartmouth, Team 5-7, Martin Fall 2016 Membro di UMass Dartmouth, Team 5-7, Martin Fall 2016

UMASSD-MARTIN-F16S5G7

3 Membri

10 Guide realizzate

2 Commenti

My USB port broke off so is there anyway I could save my videos that where om there

Corrina Guerrero - Replica

Where do you purchase the replacement usb connector?

DeEtte Moore - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 8

Ultimi 30 Giorni: 19

Tutti i Tempi: 1,057