Salta al contenuto principale
Unisciti alla Community delle riparazioni - Crea un account
Flip Video LCD Screen

Flip Video LCD Screen

Elizabeth

Elizabeth e 5 altri collaboratori

Ultimo aggiornamento il 15 apr 2021

Nessuna stima
Moderato

Introduzione

Vai al passo 1

This guide will show you how to disassemble your flip video and replace the LCD screen.

Cosa ti serve

Strumenti

  • Phillips #00 Screwdriver
    Phillips #00 Screwdriver
  • Spudger
    Spudger

Mostra di più…

  1. Flip Video LCD Screen, Outer Shell: passo 1, immagine 1 di 2 Flip Video LCD Screen, Outer Shell: passo 1, immagine 2 di 2
    • Turn off the device and take the batteries out.

    • Remove metal sticker under the LCD screen with a spudger.

    • This may require a large force to pry off the glued sticker.

  2. Flip Video LCD Screen: passo 2, immagine 1 di 1
    • Remove the 4 gray screw caps with the spudger. These cover the screw heads and protect from dirt or grime.

  3. Flip Video LCD Screen: passo 3, immagine 1 di 2 Flip Video LCD Screen: passo 3, immagine 2 di 2
    • Remove the 5 10mm screws with the #00 Phillips screwdriver. These connect the back of the outer shell to the front of the outer shell.

  4. Flip Video LCD Screen: passo 4, immagine 1 di 1
    • Open battery door. This can be done by gently depressing and sliding the battery down downward.

  5. Flip Video LCD Screen: passo 5, immagine 1 di 1
    • Use the spudger to separate outer shells.

    • The spudger must be inserted between the shell halves to pry the edges apart.

    • Slowly work around the outside to separate the halves.

  6. Flip Video LCD Screen, Circuit Board: passo 6, immagine 1 di 1
    • Remove the 3 5mm screws securing the circuit board to the front shell with the #00 Phillips screwdriver.

  7. Flip Video LCD Screen: passo 7, immagine 1 di 1
    • Slowly lift the left side of the circuit board.

    • Do not attempt to remove the circuit board completely yet. It is still connected to the device.

  8. Flip Video LCD Screen: passo 8, immagine 1 di 1
    • Disconnect the USB port cable from the back side of the circuit board.

  9. Flip Video LCD Screen: passo 9, immagine 1 di 1
    • Slide out the battery contacts.

    • Battery contacts

    • Slot where battery contacts were located

  10. Flip Video LCD Screen, LCD Screen: passo 10, immagine 1 di 1
    • With the LCD screen facing away from you, remove the 2 bronze 3 mm screws securing the LCD using the #00 Phillips screwdriver.

  11. Flip Video LCD Screen: passo 11, immagine 1 di 1
    • Flip over the circuit board and unlock the two black tabs on the ribbon connector by sliding them upwards.

  12. Flip Video LCD Screen: passo 12, immagine 1 di 1
    • Gently pull out ribbon cable.

    • If the ribbon cable does not come out easily you may not have fully unlocked the ribbon cable connector in the previous step.

    • The LCD screen is now removed and can be replaced.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Preparati per le riparazioni future

Acquista tutti

Elizabeth

Membro da: 04/15/10

100 Reputazione

6 Guide realizzate

Team

Cal Poly, Team 26-21, Regan Spring 2010 Membro di Cal Poly, Team 26-21, Regan Spring 2010

CPSU-REGAN-S10S26G21

4 Membri

12 Guide realizzate

0Commenti sulla guida

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 24

Tutti i Tempi: 5,332