Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement

Introduzione

This guide shows how to remove the paper eject frame assembly Constant paper jams might be caused by a faulty paper eject frame assembly. This process requires the knowledge of how to use basic tools.

Cosa ti serve

  1. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement, Housing: passo 1, immagine 1 di 1

    • Turn off the printer.

    • Disconnect all data connections coming into the printer such as USB, networkd cables, firewire, etc. as well as removing the power cord.

    Traduci

  2. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 2, immagine 1 di 2 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 2, immagine 2 di 2

    • Locate the IEEE cover in the back.

    • Gently slide the cover to the right to unlatch, then pull to remove it.

    Traduci

  3. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 3, immagine 1 di 2 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 3, immagine 2 di 2

    • Using a Phillips #2 screwdriver, remove the four 10 mm screws shown.

    • Remove the 6 mm screw that holds the rear housing in place.

    Traduci

  4. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 4, immagine 1 di 2 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 4, immagine 2 di 2

    • Remove the rear housing by pulling it backwards.

    Traduci

  5. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 5, immagine 1 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 5, immagine 2 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 5, immagine 3 di 3

    • Insert a plastic opening tool into the cutouts of the lower housing.

    • Release the two tabs of the side housing by lifting the tool in an upward motion.

    • Remove the side housing by pulling it outwards.

    Traduci

  6. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 6, immagine 1 di 2 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 6, immagine 2 di 2

    • Both side housings are attached by the same type of mechanism.

    • Using the same method, remove the other side housing.

    Traduci

  7. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 7, immagine 1 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 7, immagine 2 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 7, immagine 3 di 3

    • Lift the paper support.

    • Open the printer cover and front cover.

    Traduci

  8. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 8, immagine 1 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 8, immagine 2 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 8, immagine 3 di 3

    • Remove the four 10 mm Phillips #2 screws from the sides of the printer.

    • Remove the three 6 mm Phillips #2 screws.

    Traduci

  10. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 9, immagine 1 di 2 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 9, immagine 2 di 2

    • Detach the tabs from the pins on each side by pulling it outwards.

    Traduci

  11. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 10, immagine 1 di 2 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 10, immagine 2 di 2

    • Remove the two 10 mm Phillips #2 screws on the front of the printer.

    Traduci

  12. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 11, immagine 1 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 11, immagine 2 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 11, immagine 3 di 3

    • Disconnect the two cables on the side by carefully pulling it outwards.

    • You may need to gently rock the two cables up and down while pulling.

    Traduci

  13. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 12, immagine 1 di 2 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 12, immagine 2 di 2

    • Remove the upper housing by lifting it upwards.

    • It's easier to lift the housing by gripping it from the bottom.

    Traduci

  14. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement, Paper Eject Frame Assembly: passo 13, immagine 1 di 2 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement, Paper Eject Frame Assembly: passo 13, immagine 2 di 2

    • Hold the ink tube and draw out the waste ink tube by pulling on both tubes in opposite directions.

    Traduci

  15. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 14, immagine 1 di 2 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 14, immagine 2 di 2

    • Remove the acetate tape that secure the connector cable.

    Traduci

  16. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 15, immagine 1 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 15, immagine 2 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 15, immagine 3 di 3

    • There are six screws that secure the printer mechanism.

    • Using the #2 Phillips screwdriver, remove the three 10mm screws shown.

    Traduci

  17. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 16, immagine 1 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 16, immagine 2 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 16, immagine 3 di 3

    • Using the #2 Phillips screwdriver, remove the last three 10mm screws securing the printer mechanism.

    Traduci

  18. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 17, immagine 1 di 2 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 17, immagine 2 di 2

    • Remove printer mechanism from lower housing by holding the handles and lifting it upwards.

    Traduci

  19. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 18, immagine 1 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 18, immagine 2 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 18, immagine 3 di 3

    • Remove the CD-R unit housing by releasing the two attaching points to the tray base.

    • Pull it outwards diagonally one side at a time.

    Traduci

  20. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 19, immagine 1 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 19, immagine 2 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 19, immagine 3 di 3

    • Remove the left frame support plate by removing the two 6mm screws that secure it.

    • Pull it out by hand to free it.

    Traduci

  21. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 20, immagine 1 di 2 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 20, immagine 2 di 2

    • Using the #2 Phillips screwdriver, remove the four 6mm screws.

    • Remove the two 8mm screws.

    • The screws are located on the lower sections of the printer.

    Traduci

  22. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 21, immagine 1 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 21, immagine 2 di 3 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 21, immagine 3 di 3

    • Two guide pins secure the paper EJ assy in place.

    • Remove the two guide pins on the CD/DVD tray base by pulling each pin outward.

    Traduci

  23. Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 22, immagine 1 di 2 Epson Stylus Photo 1400 Paper Eject Frame Assembly Replacement: passo 22, immagine 2 di 2

    • Remove the paper EJ frame assy by pulling the it towards you.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 41 persone hanno completato questa guida.

Autore

con 9 altri collaboratori

Larry Huang

Membro da: 10/12/11

1.004 Reputazione

4 Guide realizzate

Distintivi: 15

+12 altri distintivi

Team

Cal Poly, Team 17-11, Regan Fall 2011 Membro di Cal Poly, Team 17-11, Regan Fall 2011

CPSU-REGAN-F11S17G11

4 Membri

12 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 14

Ultimi 30 Giorni: 59

Tutti i Tempi: 21,043