Salta al contenuto principale

Disassembling Sony Clie PEG-SL10

Cosa ti serve

  1. Disassembling Sony Clie PEG-SL10, Disassembling Sony Clie PEG-SL10: passo 1, immagine 1 di 1
    • Start by holding your Sony Clie PEG-SL10 face-up in your hand.

  2. Disassembling Sony Clie PEG-SL10: passo 2, immagine 1 di 1
    • Turn over your Sony Clie and unlock the cover slide lock.

  3. Disassembling Sony Clie PEG-SL10: passo 3, immagine 1 di 1
    • After unlocking the cover slide lock, remove the cover and set aside.

  4. Disassembling Sony Clie PEG-SL10: passo 4, immagine 1 di 1
    • Turn your Sony Clie face-up.

    • Using a Phillips #0 screwdriver, remove the six case screws on the sides and bottom of the device.

  5. Disassembling Sony Clie PEG-SL10: passo 5, immagine 1 di 1
    • Remove the front case by gently lifting away from the device.

  6. Disassembling Sony Clie PEG-SL10: passo 6, immagine 1 di 1
    • Turn the Sony Clie face down and open the back case by prying open the left side of the device.

    • It will open like a book connected by hinges on the right side.

  7. Disassembling Sony Clie PEG-SL10: passo 7, immagine 1 di 1
    • Gently pry off the right side off the back panel and set it aside, leaving room for the scroll wheel at the upper right corner.

  8. Disassembling Sony Clie PEG-SL10: passo 8, immagine 1 di 1
    • Using a Phillips #0 screwdriver, remove the two screws holding the scroll wheel in place.

  9. Disassembling Sony Clie PEG-SL10: passo 9, immagine 1 di 1
    • Pull out both sides of the clip to remove the scroll wheel power cable from the device.

  10. Disassembling Sony Clie PEG-SL10: passo 10, immagine 1 di 1
    • Using a Phillips #0 screwdriver, unscrew the two screws towards the bottom sides of the Sony Clie to remove the battery harness.

  11. Disassembling Sony Clie PEG-SL10: passo 11, immagine 1 di 1
    • Pull the power cable from the socket located above the upper right side of the battery harness.

  12. Disassembling Sony Clie PEG-SL10: passo 12, immagine 1 di 1
    • Gently pull out the clips to remove the bottom power cables from the motherboard after removing the battery harness.

  13. Disassembling Sony Clie PEG-SL10: passo 13, immagine 1 di 1
    • Rotate the motherboard 180 degrees so that it is upside down facing toward you to expose the power cables on the other side.

  14. Disassembling Sony Clie PEG-SL10: passo 14, immagine 1 di 1
    • Gently pull out the clips to remove the top power cables from the motherboard.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Documenti Allegati

Steve

Membro da: 10/18/11

9 Reputazione

1 Guida realizzata

Team

James Madison, Team 1-4, Allen Fall 2011 Membro di James Madison, Team 1-4, Allen Fall 2011

JMU-ALLEN-F11S1G4

3 Membri

4 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 12

Tutti i Tempi: 1,693