Aggiusta la tua roba Comunità Store

Questa guida ha delle modifiche più recenti. Passa all'ultima versione non verificata.

Disassembling Kodak Easyshare C813 Back Cover

Introduzione

This tutorial demonstrates how to remove the back cover from the camera

Cosa ti serve

  1. Disassembling Kodak Easyshare C813 Back Cover, Battery: passo 1, immagine 1 di 1

    • Turn off camera by firmly pressing the power button that is located on the top of the camera near the selector dial.

    Traduci

  2. Disassembling Kodak Easyshare C813 Back Cover: passo 2, immagine 1 di 3 Disassembling Kodak Easyshare C813 Back Cover: passo 2, immagine 2 di 3 Disassembling Kodak Easyshare C813 Back Cover: passo 2, immagine 3 di 3

    • Press thumb firmly on battery door and slide it in the direction of the arrow.

    • Lift thumb allowing the door to swing open.

    Traduci

  3. Disassembling Kodak Easyshare C813 Back Cover, Back Cover: passo 3, immagine 1 di 1

    • Before removing back cover, it is advisable to use an anti-static wrist strap to prevent damage to electronics.

    Traduci

  5. Disassembling Kodak Easyshare C813 Back Cover: passo 4, immagine 1 di 1

    • Turn the camera off by firmly pressing the power button located on top of the camera.

    Traduci

  6. Disassembling Kodak Easyshare C813 Back Cover: passo 5, immagine 1 di 3 Disassembling Kodak Easyshare C813 Back Cover: passo 5, immagine 2 di 3 Disassembling Kodak Easyshare C813 Back Cover: passo 5, immagine 3 di 3

    • Locate the 7 screws holding the back cover on.

    • Three screws are located on the bottom of the camera.

    • Two screws are located on the side shown in the photograph.

    • Two final screws are located on the opposite side shown in the photograph.

    Traduci

  7. Disassembling Kodak Easyshare C813 Back Cover: passo 6, immagine 1 di 3 Disassembling Kodak Easyshare C813 Back Cover: passo 6, immagine 2 di 3 Disassembling Kodak Easyshare C813 Back Cover: passo 6, immagine 3 di 3
    Attrezzo utilizzato in questo passaggio:
    Phillips #00 Screwdriver
    $5.49
    Compra

    • Remove all 7 screws:

    • Hold the camera firmly with one hand so that you can still see a screw.

    • Place the Philips 00(Found here)screwdriver into the screw.

    • Turn the screwdriver to the left until it is free.

    • Repeat for the remaining screws.

    Traduci

  8. Disassembling Kodak Easyshare C813 Back Cover: passo 7, immagine 1 di 3 Disassembling Kodak Easyshare C813 Back Cover: passo 7, immagine 2 di 3 Disassembling Kodak Easyshare C813 Back Cover: passo 7, immagine 3 di 3

    • Use plastic opening tools to slightly open the side of the case.

    • Insert a plastic opening tool and apply pressure to the internal three tabs at the top.

    • The first two are near the words "3X Optical Zoom".

    • The third is near the shutter button.

    Traduci

  9. Disassembling Kodak Easyshare C813 Back Cover: passo 8, immagine 1 di 3 Disassembling Kodak Easyshare C813 Back Cover: passo 8, immagine 2 di 3 Disassembling Kodak Easyshare C813 Back Cover: passo 8, immagine 3 di 3

    • Gently pull apart the back cover from the rest of the camera.

    • Make sure there are no more screws or tabs keeping the cover on.

    • Use the plastic opening tool to separate any sides still closely connected.

    Traduci
Linea Traguardo

Un'altra persona ha completato questa guida.

Autore

con 7 altri collaboratori

Susan Marano

Membro da: 04/15/10

336 Reputazione

7 Guide realizzate

Distintivi: 16

+13 altri distintivi

Team

Cal Poly, Team 24-22, Regan Spring 2010 Membro di Cal Poly, Team 24-22, Regan Spring 2010

CPSU-REGAN-S10S24G22

4 Membri

20 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 5

Ultimi 7 Giorni: 15

Ultimi 30 Giorni: 19

Tutti i Tempi: 2,382