Salta al contenuto principale

Disassembling Insignia Flex 8 Circuit Board

Cosa ti serve

  1. Disassembling Insignia Flex 8 Circuit Board, Circuit Board: passo 1, immagine 1 di 1
    • Turn off the power to your tablet to avoid injury.

    • Position the tablet so that the screen is face down and the power button is located in the upper left hand corner.

    • Hold down the power button for five seconds until the tablet powers down.

  2. Disassembling Insignia Flex 8 Circuit Board: passo 2, immagine 1 di 2 Disassembling Insignia Flex 8 Circuit Board: passo 2, immagine 2 di 2
    • Remove the back casing from the screen by sliding a credit card or a similarly thin but firm object in between the casing and the screen.

    • You may need to use a spudger to initially create separation between the screen and the casing.

    • Run this object around the perimeter of the tablet until there is separation between the casing and the screen.

    • Remove the back casing and set aside.

  3. Disassembling Insignia Flex 8 Circuit Board: passo 3, immagine 1 di 2 Disassembling Insignia Flex 8 Circuit Board: passo 3, immagine 2 di 2
    • Peel tape off of ribbon connectors. Starting at the power button, work clockwise around the tablet.

  4. Disassembling Insignia Flex 8 Circuit Board: passo 4, immagine 1 di 3 Disassembling Insignia Flex 8 Circuit Board: passo 4, immagine 2 di 3 Disassembling Insignia Flex 8 Circuit Board: passo 4, immagine 3 di 3
    • To remove the camera ribbon cable, lift the flap using a spudger.

    • Pull the ribbon directly back to release it.

  5. Disassembling Insignia Flex 8 Circuit Board: passo 5, immagine 1 di 3 Disassembling Insignia Flex 8 Circuit Board: passo 5, immagine 2 di 3 Disassembling Insignia Flex 8 Circuit Board: passo 5, immagine 3 di 3
    • Remove the second ribbon cable by prying up the black flap using a spudger.

    • Pull the ribbon cable horizontally directly away from the battery.

  6. Disassembling Insignia Flex 8 Circuit Board: passo 6, immagine 1 di 3 Disassembling Insignia Flex 8 Circuit Board: passo 6, immagine 2 di 3 Disassembling Insignia Flex 8 Circuit Board: passo 6, immagine 3 di 3
    • Remove the final ribbon cable by pulling back the two black tabs on either side of the ribbon cable.

    • Pull the ribbon horizontally directly away from the battery.

  7. Disassembling Insignia Flex 8 Circuit Board: passo 7, immagine 1 di 2 Disassembling Insignia Flex 8 Circuit Board: passo 7, immagine 2 di 2
    • Unscrew the thirteen 4.75mm screws around the perimeter of the tablet using a PH 00 screwdriver.

  8. Disassembling Insignia Flex 8 Circuit Board: passo 8, immagine 1 di 2 Disassembling Insignia Flex 8 Circuit Board: passo 8, immagine 2 di 2
    • Unscrew the four 3.75mm screws and plastic washers using a PH 00 screwdriver.

    • Lift up the circuit board.

  9. Disassembling Insignia Flex 8 Circuit Board: passo 9, immagine 1 di 1
    • Unscrew the final two screws that were underneath the circuit board.

    • These screws are near the charging port and USB adapter.

    • These screws are also 3.75mm and can be interchanged with the second set of screws only.

  10. Disassembling Insignia Flex 8 Circuit Board: passo 10, immagine 1 di 1
    • Lift the circuit board and black internal mounting piece away from the screen.

    • Set the circuit board aside.

    • Be careful of the soldered antenna as you separate the pieces.

    • Be careful of the soldered ribbon that is connected to the power source. This ribbon is fragile.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

2 Commenti

Whwre can i buy the new screen

Emmanuel - Replica

I don’t see the ssd, and way to upgrade the internal sad had?

William Henderson - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 6

Tutti i Tempi: 4,905