Salta al contenuto principale

Cosa ti serve

Questo smontaggio non è una guida di riparazione. Per riparare il tuo Dell Latitude D620, usa il nostro manuale di assistenza.

  1. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 1, immagine 1 di 2 : passo 1, immagine 2 di 2
    • Open the laptop's screen 180 Degrees so it is straight back.

    • Use a flat head screwdriver or a spudger to pry the top bezel off. Work it side to side until the bezel is freed from the chassis, exposing 3 screws

  2. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 2, immagine 1 di 1
    • Remove the 3 Phillips screws securing the keyboard.

    • Just remember to keep your screws organized! It will make everything much easier.

  3. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 3, immagine 1 di 2 : passo 3, immagine 2 di 2
    • Use your fingers to carefully lift up the keyboard. Refer to the first picture for guidance.

    • Carefully pull the keyboard upwards toward the LCD screen so it can be released from the bottom tabs.

    • Carefully lift the keyboard so the keys are resting on the palmrest, this will expose the ribbons for the keyboard, trackpad and Tracking Nub.

  4. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 4, immagine 1 di 2 : passo 4, immagine 2 di 2
    • First insert a small flat head screwdriver or a spudger into the small notch in between holding down the ribbon.

    • Then grab the metal bar on top of the keyboard connector and pull straight up. The cable should come free.

  5. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 5, immagine 1 di 2 : passo 5, immagine 2 di 2
    • Grab the top of the display connector and pull it straight up and out.

    • This connector requires a little more force than the others, so it may take some effort.

  6. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 6, immagine 1 di 3 : passo 6, immagine 2 di 3 : passo 6, immagine 3 di 3
    • Use a tool or your fingers to gently remove the antenna cables from the wireless card.

  7. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 7, immagine 1 di 3 : passo 7, immagine 2 di 3 : passo 7, immagine 3 di 3
    • Pull back the clips by the antenna connectors, and the card should rise up on its own. Gently remove the card from its socket.

  8. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 8, immagine 1 di 3 : passo 8, immagine 2 di 3 : passo 8, immagine 3 di 3
    • Not all devices have a WWAN Card, so most people can skip this step.

    • Using similar procedures as the WLAN, disconnect the single antenna cable, push the rear clips back and remove the card.

  9. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 9, immagine 1 di 2 : passo 9, immagine 2 di 2
    • Close the laptop screen completely, make sure it clips in place.

    • Follow the Green bullet first then move onto the Blue bullet.

    • Make sure no cables or parts get caught in the hinge.

    • The bottom screw is labeled with D, remove it.

    • The screw on the rear is not labeled, remove it as well.

    • Repeat this for the opposite side of the laptop.

  10. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 10, immagine 1 di 2 : passo 10, immagine 2 di 2
    • Very, VERY carefully open up the screen so it is at a 90° angle with the palmrest.

    • Pull it straight up, making sure all cables are free of their routing ares.

  11. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 11, immagine 1 di 3 : passo 11, immagine 2 di 3 : passo 11, immagine 3 di 3
    • Remove all of the remaining screws on the laptop with a Phillips screwdriver.

    • There are screws on the top under the keyboard as well, remove those.

    • All of the screws with a P by them means they secure the palmrest. This will help you keep organized.

  12. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 12, immagine 1 di 2 : passo 12, immagine 2 di 2
    • Seperate the palmrest from the device, starting from the back by sliding it forward and pulling it most of the way off.

    • Don't remove it completely, there is still one connector attached.

  13. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 13, immagine 1 di 1
    • Pull the trackpad connector straight out of the motherboard.

    • Don't pull on it by the cables, grab as close to the socket as you can.

  14. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 14, immagine 1 di 2 : passo 14, immagine 2 di 2
    • With a Phillips screwdriver, remove the 4 screws on the heatsink, in order of the numbers of the metal.

    • Loosening the screws out of order can be damaging.

  15. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 15, immagine 1 di 3 : passo 15, immagine 2 di 3 : passo 15, immagine 3 di 3
    • Grab the heatsink and remove it, it may require force.

    • There is still thermal paste and a thermal pad attached.

  16. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 16, immagine 1 di 3 : passo 16, immagine 2 di 3 : passo 16, immagine 3 di 3
    • Clean the remaining thermal compound off of the CPU. Remove the thermal pad if it is still stuck to the GPU.

  17. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 17, immagine 1 di 3 : passo 17, immagine 2 di 3 : passo 17, immagine 3 di 3
    • Several more photos of the Intel Core Duo.

  18. Questo passaggio è privo di traduzione. Aiuta a tradurlo

    : passo 18, immagine 1 di 3 : passo 18, immagine 2 di 3 : passo 18, immagine 3 di 3
    • Gently turn the screw above the socket and lift the CPU out.

    • The End!

Nicholas Ouimet

Membro da: 10/16/09

3.476 Reputazione

12 Guide realizzate

8 Commenti

Seems like it would make a perfect "Hackintosh."

Chris Green - Replica

Citazione da Chris Green:

Seems like it would make a perfect "Hackintosh."

Yes. It does indeed. I've been using it as a hackintosh sense early February. I had Mac OSX 10.6.2 on it, even before I performed this tear down. I was able to use software updater to go strait from 10.6.0 to 10.6.2. Skipping 10.6.1. I've only had a few kernel panics. I've even been using the iPhone SDK. It is a very stable hackintosh. The GMA 950 can even play The SIms 3 w/o any issues.

Nicholas Ouimet - Replica

Fantastic guide!! Thank you for taking the time and effort to create it!

Steve Weinrich - Replica

There is a little flat, white, Multi-wire connector in the upper-left corner.

I suspect that this is where the optional Bluetooth module would be located, can anyone confirm this?

Thanks,

Tim D.

Tim downing - Replica

Yes, the flat white connector on the left side above the keyboard is for the optional bluetooth connector. It interfaces via USB.

souta95 -

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 13

Ultimi 30 Giorni: 38

Tutti i Tempi: 68,915